|
Codice progetto |
Codice Norma |
Titolo |
Sommario |
Pubblicazione UNI |
|
|
00156035 |
EN 14239:2004 |
Ventilation for buildings - Ductwork - Measurement of ductwork surface area |
To specify a method for the measurement and calculation of the surface area of ductwork and ductwork components. |
Sì
|
|
|
00156049 |
EN 12589:2001 |
Ventilation for buildings - Air terminal units - Aerodynamic testing
and rating of constant and variable rate terminal units |
This European Standard specifies methods for the aerodynamic testing and rating of constant and
variable flow rate terminal units suitable for use with air distribution systems.
The tests in this standard are designed to determine fully the aerodynamic performance of terminal units
and provide a basis for the comparison of the suitability of such assemblies when correctly installed in an
air distribution system. |
Sì
|
|
|
00156076 |
EN 12792:2003 |
Ventilation for buildings - Symbols, terminology and graphical symbols |
This European Standard specifies symbols, units and terminology ventilation systems for buildings. |
Sì
|
|
|
00156081 |
EN 14240:2004 |
Ventilation for buildings - Chilled ceilings - Testing and rating |
This European Standard specifies test conditions and methods for the determination of the cooling capacity of chilled ceilings and other extended chilled surfaces.The purpose of the Standard is to give comparable and repeatable product data.The test method applies to all types of surface cooling systems using any medium as energy transport medium. NOTE The result is valid only for the specified test set up. For other conditions (i.e. different positions of heat loads, forced flow around the test object, variations in surface area) the producer should give guidance based on full-scale tests.This standard refers to water as the cooling medium throughout, however wherever water is specified any other cooling medium can also be used in the test. Where air is the transport medium this air may not be discharged into the test room. In addition, this standard refers to chilled surfaces and where "surfaces" are specified this should be taken to include ceiling, wall or floor as appropriate. |
Sì
|
|
|
00156041 |
EN 12237:2003 |
Ventilation for buildings - Ductwork - Strength and leakage of circular sheet metal ducts |
This European Standard specifies requirements and test methods for strength and air leakage of circular ductwork
used in air conditioning and ventilation systems in buildings.
The standard is intended to establish the mechanical strength and leakage required to verify the fitness for the
intended service as installed ductwork.
The standard is intended for testing specific installations as well as product series in general under in-situ or laboratory conditions. The requirements and methods are applicable also to rectangular ductwork in respect of air leakage. |
Sì
|
|
|
00156038 |
EN 13180:2001 |
Ventilation for buildings - Ductwork - Dimensions and mechanical requirements for flexible ducts |
This standard specifies requirements and test methods for the technical characteristics of flexible ducts used in ventilation and air conditioning installations in buildings for human occupancy. |
Sì
|
|
|
00156061 |
EN 13181:2001 |
Ventilation for buildings - Terminals. Performance testing of louvres subject to simulated sand |
This European Standard specifies a method for measuring the sand rejection efficiency of sand trap louvres subject to simulated sand and with inlet air flow through the louvre under test. The standard consider a 1000 mm x 1000 mm section of sand trap louvre, or the nearest possible blade increment, for evaluation purposes |
Sì
|
|
|
00156063 |
EN 13182:2002 |
Ventilation for buildings. Insturmentation reqirements for air velocity measurements in ventilated spaces. |
This standard specifies the main characteristics of air velocity measuring devices. This includes requirements for thermal velocity probes, recalibration and the signal processing of measurements in a ventilated space, including those in the air jet and in the occupied zone. |
Sì
|
|
|
00156036 |
EN 12236:2002 |
Ventilation for buildings. Ductwork hangers and supports. Requirementes for strength |
This standard specifies requirements for the construction and application of supports for sheet metal ductwork in ventilation and ari conditioning systems. |
Sì
|
|
|
00156082 |
EN 14518:2005 |
Ventilation for buildings - Chilled beams - Testing and rating of passive chilled beams |
This European Standard specifies test conditions and methods for the determination of the cooling capacity of chilled beams or other similar systems with free convection, i.e. without forced air flow.Also included is the method to determine local air velocity and temperature below the beam. |
Sì
|
|
|
00156065 |
EN 13264:2001 |
Ventilation for buildings - Floor mounted air terminal devices -Tests for structural classification |
The document specifies structural classifications for floor mounted air terminal devices in respect of their possible applications and related structural test methods: a) static test methods; b) impact test methods; c) dynamic test methods |
Sì
|
|
|
00156047 |
EN 12238:2001 |
Ventilation for buildings - Air terminal devices - Aerodynamic
testing and rating for mixed flow application |
This European Standard specifies methods for the laboratory aerodynamic testing and rating of air
terminal devices for mixed flow applications, including the specification of suitable test facilities and
measurement techniques.
The standard gives only tests for the assessment of characteristics of the air terminal devices under
isothermal conditions.
The testing of low velocity air terminal devices is specified in EN 12239. |
Sì
|
|
|
00156050 |
EN 13030:2001 |
Ventilation for buildings - Terminals - Performance testing of louvres subjected to simulated rain |
This standard specifies a method for measuring the water rejection performance of louvres subject to simulated rain and wind pressures, both with and without air flow through the louvre under test. |
Sì
|
|
|
00156060 |
EN 12239:2001 |
Ventilation for buildings - Air termal devices - Aerodynamic testing and rating for displacement flow applications |
This European Standard specifies methods for the laboratory aerodynamic testing and rating of low
velocity air terminal devices for displacement flow applications, including the specification of suitable test
facilities and measurement techniques.
The standard gives only tests for the assessment of characteristics of the air terminal devices under non-isothermal
conditions. |
Sì
|
|
|
00156108 |
EN 15650:2010 |
Ventilation for buildings - Fire dampers |
This European standard applies to fire dampers that are to be used in conjunction with partitions to maintain fire compartments. This standard specifies requirements and gives reference to the test methods defined for fire dampers, which are intended to be installed in Heating, Ventilating and Air Conditioning (HVAC) installations in buildings.
Details are given for the provision of evaluation of conformity and marking of fire dampers. Fire dampers meeting requirements of this standard may be considered suitable for both ducted and unducted applications.
|
Sì 26/05/2010
|
|
|
00156105 |
EN 15665:2009 |
Ventilation for buildings - Determining performance criteria for residential ventilation systems |
This European Standard sets out criteria to assess the performance of residential ventilation systems (for new, existing and refurbished buildings) which serve single family, multi family and apartment type dwellings throughout the year. This European Standard specifies ways to determine performance criteria to be used for design levels in regulations and/or standards. These criteria are meant to be applied to, in particular: - mechanically ventilated building (mechanical exhaust, mechanical supply or balanced system); - natural ventilation with stack effect for passive ducts; - hybrid system switching between mechanical and natural modes; - windows opening by manual operation for airing or summer comfort issues. This European Standard considers aspects of hygiene and indoor air quality. Health risk from exposure to tobacco smoke is excluded from this European Standard. |
Sì
|
|
|
00156086 |
EN 12097:2006 |
Ventilation for buildings - Ductwork - Requirements for ductwork components to facilitate maintenance of ductwork systems |
This prestandard applies to ductwork in buildings for human occupancy. It specifies the dimensions, shape and location requirements for openings, access and inspection covers and access doors for cleaning and service in ductwork. It applies to ductwork which is in accordance to standards prEN 1505, prEN 1506 and prEN XXXD. |
Sì
|
|
|
00156109 |
EN 1506:2007 |
Ventilation for buildings - Sheet metal air ducts and fittings with circular cross-section - Dimensions |
This European Standard specifies dimensions of ducts and duct fittings with circular cross- section. It applies to ductwork used in ventilating and air conditioning systems in buildings, subject to human occupancy. The wall thickness of ducts and fittings is not specified in this standard; strength and leakage are dealt with in EN 12237. |
Sì
|
|
|
00156104 |
EN 1507:2006 |
Ventilation for buildings - Sheet metal air ducts with rectangular section - Requirements for strenght and leakage |
The European Standard applies to rectangular ductwork of sheet metal used in air conditioning and ventilation systems defined in the principal scope of CEN/TC 156. |
Sì
|
|
|
00156071 |
EN 14277:2006 |
Ventilation for buildings - Air terminal devices - Method for airflow measurement by calibrated sensors in or close to ATD/plenum boxes |
This European Standard specifies methods for the laboratory aerodynamic testing and rating of the air flow rate measurement accuracy of fixed air flow rate measurement devices, including supply and exhaust air terminal devices (ATD) and in-duct measurement stations (IMS) and the sensitivity of such devices to flow disturbance. A general overview of different test configurations is shown in Figure 1. |
Sì
|
|
|
Codice progetto |
Codice Norma |
Titolo |
Sommario |
Pubblicazione UNI |
|
|
00156058 |
EN 15243:2007 |
Ventilation for buildings - Calculation of room temperatures and of load and energy for buildings with room conditioning systems |
The scope of this European Standard is:
- To define the procedure how the calculation methods to determine the temperatures, sensible loads and energy demands for the rooms shall be used in the design process.
- To describe the calculation methods to determine the latent room cooling and heating load, the building heating, cooling, humidification and dehumidification loads and the system heating, cooling, humidification and dehumidification loads.
- To define the general approach for the calculation of the overall energy performance of buildings with room conditioning systems.
- To describe one or more simplified calculation methods for the system energy requirements of specific system types, based on the building energy demand result from prEN ISO 13790, and to define their field of application.
A general framework standard is given which imposes an hourly calculation for all cases which cannot be covered by simplified methods, and gives requirements on what has to be taken into account. Input and output data are defined. |
Sì
|
|
|
00156C01 |
EN 12599:2000/AC:2002 |
Ventilation for buildings - Test procedures and measuring methods for handing over installed ventilation and air conditioning systems |
This European Standard specifies checks, test methods and measuring instruments in order to verify the fitness for purpose of the installed systems at the stage of handing over. The Standard enables the choice between simple test methods, when sufficient, and extensive measurements, when necessary. The Standard applies to mechanically operated ventilation and air conditioning systems as specified in CR 12792 and comprising any of the following: - air terminal devices and units; - air handling units; - air distribution systems (supply, extract, exhaust); - fire protection devices; - automatic control devices. |
Sì
|
|
|
00156C04 |
EN 13182:2002/AC:2002 |
Ventilation for buildings - Instrumentation requirements for air velocity measurements in ventilated spaces |
This standard specifies the main characteristics of air velocity measuring devices. This includes requirements for thermal velocity probes, recalibration and the signal processing of measurements in a ventilated space, including those in the air jet and in the occupied zone. Other types of velocity measuring devices should fulfil the performance parameters stated but appropriate calibration techniques should not necessarily be used which are described in this standard |
Sì
|
|
|
00156098 |
EN 15240:2007 |
Ventilation for buildings - Energy performance of buildings - Guidelines for inspection of air-conditioning systems |
This European Standard describes the common methodology for inspection of air conditioning systems in buildings for space cooling and or heating from an energy consumption standpoint. |
Sì
|
|
|
00156077 |
EN 15242:2007 |
Ventilation for buildings - Calculation methods for the determination of air flow rates in buildings including infiltration |
This European standard describe the method to calculate the ventilation air flow rates for buildings to be used for applications such as energy calculations, heat and cooling load calculation, summer comfort and indoor air quality evaluation |
Sì
|
|
|
00156099 |
EN 15239:2007 |
Ventilation for buildings - Energy performance of buildings - Guidelines for inspection of ventilation systems |
To develop the methodology for inspection of mechanical and natural ventilation systems from an energy consumption standpoint. This standard applies to residential and non residential buildings. |
Sì
|
|
|
00156101 |
EN 13779:2007 |
Ventilation for non-residential buildings - Performance requirements for ventilation and room-conditioning systems |
This document applies to the design of ventilation and room conditioning systems for non-residential buildings subject to human occupancy. |
Sì
|
|
|
00156074 |
EN 13403:2003 |
Ventilation for buildings - Non-metallic ducts - Ductwork made from insulation ductboards |
This European Standard contains the basic requirements and characteristics for ductwork made of insulation ductboards, and used in ventilation and air conditioning systems of buildings, subject to human occupancy. |
Sì 07/04/2011
|
|
|
00156131 |
EN ISO 12499:2008 |
Industrial fans - Mechanical safety of fans - Guarding (ISO 12499:1999) |
This European Standard specifies requirements for the mechanical guarding of industrial fans. The circumstances under which safety measures shall be taken are described and information on how hazards can be reduced or eliminated is given, along with guidance on safety practices and information for use. |
Sì
|
|
|
00156094 |
EN 13141-8:2006 |
Ventilation for buildings - Performance testing of components/products for residential ventilation - Part 8: Performance testing of un-ducted mechanical supply and exhaust vent. units (including heat recovery) for mechanical ventilation systems intended for a single room |
This European Standard specifies the laboratory test methods and test requirements for the testing of aerodynamic, thermal and acoustic performance, and the electrical power of a un-ducted mechanical supply and exhaust ventilation unit used in a single room. In general, such a unit contains: ¾ supply and exhaust air fans; ¾ air filters; ¾ air to air heat exchanger for exhaust air heat recovery; ¾ control system. Such equipment can be provided in more than one assembly, the separate assemblies of which are designed to be used together. This European Standard does not deal with ducted units or units with heat pumps. Safety requirements are given in EN 60335-2-80. |
Sì
|
|
|
00156087 |
EN 1886:2007 |
Ventilation for buildings - Air handling units - Mechanical performance |
This standard specifies test methods, test requirements and classifications for air handling units, which are supplying and/or extracting air via a ductwork ventilating/conditioning a part or the whole of the building. Except for the thermal and acoustic performance of the casing, the test methods and requirements are applicable to both complete units and any separate sections. |
Sì
|
|
|
00156121 |
EN 15116:2008 |
Ventilation in buildings - Chilled beams - Testing and rating of active chilled beams |
This European Standard specifies methods for measuring the cooling capacity of chilled beams with forced air flow. The evaluation of aerodynamic air performance should be based on the requirements of WI 00156113 and the requirements set out in this standard |
Sì
|
|
|
00156107 |
EN 15423:2008 |
Ventilation for buildings - Fire precautions for air distribution systems in buildings |
This document gives guidance for system designers, installers, commissioners and maintenance teams on the incorporation of protective measures for air distribution system within buildings to prevent the initiation and the spread of fire, smoke and other by-products of combustion |
Sì
|
|
|
00156103 |
EN 13141-10:2008 |
Ventilation for buildings - Performance testing of components/products for residential ventilation - Part 10: Humidity controlled extract air terminal device |
This European Standard specifies laboratory methods for testing humidity controlled exhaust air terminal devices.
This European Standard describes tests intended to characterize:
- aero and hygro-dynamic performance;
- acoustic characteristics (including noise production of the device; insertion loss of the device; sound insulation)
- time response. |
Sì
|
|
|
00156102 |
EN 13141-9:2008 |
Ventilation for buildings - Performance testing of components/products for residential ventilation - Part 9: Externally mounted humidity controlled air transfer device |
This European Standard specifies laboratory methods for testing humidity controlled air inlets.
It applies to all devices located between one room and outside and controlled on indoor humidity.
It describes tests intended to characterise:
-aero and hygro-dynamic performance;
- air tightness when closed (for closable humidity controlled air inlet);
- air diffusion in the occupied zone;
- sound insulation;
- time response.
This European Standard does not apply to the evaluation of air filtration, condensation risk and noise production. |
Sì
|
|
|
00156119 |
EN 13141-2:2010 |
Ventilation for buildings - Performance testing of components/products for residential ventilation - Part 2: Exhaust and supply air terminal devices |
This European Standard specifies laboratory methods for testing exhaust and supply air terminal devices operating under pressure differences.
It applies to devices used in mechanical and natural residential ventilation systems, of the following types:
- device with a manually adjustable opening; or
- device with a fixed opening; or
- pressure difference controlled device.
It describes tests intended to characterize:
- flow rate/pressure;
- air diffusion characteristics (for supply air terminal devices);
- noise production for components of systems;
- nsertion loss of component of systems;
- ound insulation. |
Sì 09/09/2010
|
|
|
00156145 |
EN ISO 13349:2010 |
Fans - Vocabulary and definitions of categories (ISO/DIS 13349:2008) |
-- |
Sì 26/05/2011
|
|
|
00156143 |
UNI EN 12599:2012 |
Ventilation for buildings - Test procedures and measuring methods for hand over air
conditioning and ventilation systems |
Specifications for test procedures and measuring methods for handing over installed ventilation and air conditioning systems |
Sì 30/11/2012
|
|
|
00156147 |
EN 13141-6:2014 (UNI EN 13141-6:2015) |
Ventilation for buildings - Performance testing of components/products for residential ventilation - Part 6: Exhaust ventilation system packages used in a single dwelling |
To specify laboratory methods for testing exhaust ventilation system packages used in a single dwelling. |
Sì 05/02/2015
|
|
|
00156149 |
EN 15727:2010 |
Ventilation for buildings - Ducts and ductwork components, leakage classification and testing |
This document applies to technical ductwork products, intended for installation in ductwork conforming to EN 1505 and EN 1506, used in air conditioning and ventilation systems.
This document specifies the leakage requirements for technical ductwork products, i.e. components in the ductwork that has more functions than conveying air, such as sound attenuators, filter boxes and duct fans etc.
|
Sì 08/07/2010
|
|
|
Codice progetto |
Codice Norma |
Titolo |
Sommario |
Pubblicazione UNI |
|
|
00156152 |
UNI EN 15780:2011 |
Ventilation for buildings - Ductwork - Cleanliness of ventilation system |
Standard for cleanliness of ductwork systems to include design, commissioning and maintenance aspects. |
Sì 24/11/2011
|
|
|
00156162 |
UNI EN 16445:2013 |
Ventilation for buildings - Air Diffusion - Aerodynamic testing and rating for mixed flow application: non-isothermal procedure for cold jet |
This European Standard specifies methods for the laboratory aerodynamic testing and rating of air terminal devices for mixed flow applications, including the specification of suitable test facilities and measurement techniques. This standard applies to laboratory testing of ATD for technical characterisation.The standard gives only tests for the assessment of characteristics of the air terminal devices for mixed flow applications, under non-isothermal conditions with a cold jet. It does not cover the testing of isothermal or low velocity terminal devices which are covered by other published standards. |
Sì 20/03/2013
|
|
|
00156C05 |
UNI EN 15241:2007/AC:2011 |
Ventilation for buildings - Calculation methods for energy losses due to ventilation and infiltration in buildings |
- |
Sì 15/03/2012
|
|
|
00156174 |
UNI EN 13141-11:2015 |
Ventilation for buildings - Performance testing of components/products for residential ventilation - Part 11: Supply ventilation units |
- |
Sì 23/07/2015
|
|
|
00156176 |
UNI EN ISO 13350:2015 |
Fans - Performance testing of jet fans (ISO 13350:2015) |
- |
Sì 26/11/2015
|
|
|
00156178 |
UNI EN 16573:2017 |
Ventilation for Buildings - Performance testing of components for residential buildings - Multifunctional balanced ventilation units for single family dwellings, including heat pumps |
This Standard specifies the laboratory test methods and test requirements for aerodynamic, energy rating and acoustic performance, of multifunctional balanced units intended for use in a single dwelling. In the case of units consisting of several parts, this standard applies only to those designed and supplied as a complete package with the mount instructions. |
Sì 23/02/2017
|
|
|
00156180 |
EN ISO 5801:2017 |
Fans - Performance testing using standardized airways (ISO 5801:2017) |
- |
Sì 08/03/2018
|
|
|
00156188 |
UNI EN ISO 12759:2015 |
Fans - Efficiency classification for fans (ISO 12759:2010, including Amd 1:2013) |
- |
Sì 08/10/2015
|
|
|
00156191 |
UNI EN 16798-3:2018 (EN 16798-3:2017) |
Energy performance of buildings - Ventilation for buildings - Part 3: For non-residential buildings - Performance requirements for ventilation and room-conditioning systems (Modules M5-1, M5-4) |
- |
Sì 08/03/2018
|
|
|
00156192 |
UNI CEN/TR 16798-2:2020 (CEN/TR 16798-2:2019) |
Energy performance of buildings - Ventilation for buildings - Part 2: Interpretation of the requirements in EN 16798-1 - Indoor environmental input parameters for design and assessment of energy performance of buildings addressing indoor air quality, thermal environment, lighting and acoustics (Module M1-6) |
- |
Sì 01/10/2020
|
|
|
00156193 |
UNI EN 16798-1:2019 |
Energy performance of buildings - Ventilation for buildings - Part 1: Indoor environmental input parameters for design and assessment of energy performance of buildings addressing indoor air quality, thermal environment, lighting and acoustics - Module M1-6 |
- |
Sì 13/06/2019
|
|
|
00156194 |
UNI EN 16798-17:2018 (EN 16798-17:2017) |
Energy performance of buildings - Ventilation for buildings - Part 17: Guidelines for inspection of ventilation and air conditioning systems (Module M4-11, M5-11, M6-11, M7-11) |
- |
Sì 08/03/2018
|
|
|
00156195 |
UNI CEN/TR 16798-18:2018 (CEN/TR 16798-18:201 |
Energy performance of buildings - Ventilation for buildings - Part 18: Interpretation of the requirements in EN 16798-17 - Guidelines for inspection of ventilation and air-conditioning systems (Modules M4-11, M5-11, M6-11, M7-11) |
- |
Sì 14/06/2018
|
|
|
00156196 |
UNI CEN/TR 16798-4:2018 (CEN/TR 16798-4:2017) |
Energy performance of buildings - Ventilation for buildings - Part 4: Interpretation of the requirements in EN 16798- 3 - For non-residential buildings - Performance requirements for ventilation and room-conditioning systems(Modules M5-1, M5-4) |
- |
Sì 14/06/2018
|
|
|
00156197 |
UNI CEN/TR 16798-6:2018 (CEN/TR 16798-6:2017) |
Energy performance of buildings - Ventilation for buildings - Part 6: Interpretation of the requirements in EN 16798-5 -1 and EN 16798-5-2 - Calculation methods for energy requirements of ventilation and air conditioning systems (Modules M5-6, M5-8, M 6-5, M6-8 , M7-5, M7-8) |
- |
Sì 14/06/2018
|
|
|
00156198 |
UNI EN 16798-13:2018 (EN 16798-13:2017) |
Energy performance of buildings - Ventilation for buildings - Part 13: Calculation of cooling systems (Module M4-8) - Generation |
- |
Sì 08/03/2018
|
|
|
00156199 |
UNI CEN/TR 16798-14:2018 (CEN/TR 16798-14:201 |
Energy performance of buildings - Ventilation for buildings - Part 14: Interpretation of the requirements in EN 16798-13 - Calculation of cooling systems (Module M4-8) - Generation |
- |
Sì 14/06/2018
|
|
|
00156200 |
UNI EN 16798-15:2018 (EN 16798-15:2017) |
Energy performance of buildings - Ventilation for buildings - Part 15: Calculation of cooling systems (Module M4-7) - Storage |
- |
Sì 08/03/2018
|
|
|
00156201 |
UNI CEN/TR 16798-16:2018 (CEN/TR 16798-16:201 |
Energy performance of buildings - Ventilation for buildings - Part 16: Interpretation of the requirements in EN 16798-15 - Calculation of cooling systems (Module M4-7) - Storage |
- |
Sì 14/06/2018
|
|
|
00156202 |
UNI EN 16798-7:2018 (EN 16798-7:2017) |
Energy performance of buildings - Ventilation for buildings - Part 7: Calculation methods for the determination of air flow rates in buildings including infiltration (Modules M5-5) |
- |
Sì 08/03/2018
|
|
|
Codice progetto |
Codice Norma |
Titolo |
Sommario |
Pubblicazione UNI |
|
|
00156203 |
UNI CEN/TR 16798-8:2018 (CEN/TR 16798-8:2017) |
Energy performance of buildings - Ventilation for buildings - Part 8: Interpretation of the requirements in EN 16798-7 - Calculation methods for the determination of air flow rates in buildings including infiltration - (Module M5-5) |
- |
Sì 14/06/2018
|
|
|
00156204 |
UNI EN 16798-9:2018 (EN 16798-9:2017) |
Energy performance of buildings - Ventilation for buildings - Part 9: Calculation methods for energy requirements of cooling systems (Modules M4-1, M4-4, M4-9) - General |
- |
Sì 08/03/2018
|
|
|
00156205 |
UNI CEN/TR 16798-10:2018 (CEN/TR 16798-10:201 |
Energy performance of buildings - Ventilation for buildings - Part 10: Interpretation of the requirements in EN 16798-9 - Calculation methods for energy requirements of cooling systems (Module M4-1,M4-4, M4-9) - General |
- |
Sì 14/06/2018
|
|
|
00156208 |
UNI EN 16798-5-1:2018 (EN 16798-5-1:2017) |
Energy performance of buildings - Ventilation for buildings - Part 5-1: Calculation methods for energy requirements of ventilation and air conditioning systems (Modules M5-6, M5-8, M6-5, M6-8, M7-5, M7-8) - Method 1: Distribution and generation |
- |
Sì 08/03/2018
|
|
|
00156211 |
UNI EN ISO 5802:2015 |
EN ISO 5802:2008/A1:2015 - Industrial fans - Performance testing in situ (ISO 5802:2001/Amd 1:2015) |
- |
Sì 22/10/2015
|
|
|
00156212 |
UNI EN 16282-1:2018 (EN 16282-1:2017) |
Equipment for commercial kitchens - Components for ventilation in commercial kitchens - Part 1: General requirements including calculation method |
- |
Sì 08/03/2018
|
|
|
00156213 |
UNI EN 16282-2:2017 (EN 16282-2:2016) |
Equipment for commercial kitchens - Components for ventilation in commercial kitchens - Part 2: Kitchen ventilation hoods; design and safety requirements |
- |
Sì 19/01/2017
|
|
|
00156215 |
UNI EN 16282-4:2017 (EN 16282-4:2016) |
Equipment for commercial kitchens - Components for ventilation in commercial kitchens - Part 4: Air inlets and outlets; design and safety requirements |
- |
Sì 19/01/2017
|
|
|
00156216 |
UNI EN 16282-5:2018 (EN 16282-5:2017) |
Equipment for commercial kitchens - Components for ventilation in commercial kitchens - Part 5: Air duct; Design and dimensioning |
- |
Sì 08/03/2018
|
|
|
00156217 |
UNI EN 16282-6:2020 |
Equipment for commercial kitchens - Components for ventilation in commercial kitchens - Part 6: Aerosol separators; Design and safety requirements |
- |
Sì 27/03/2020
|
|
|
00156219 |
UNI EN 16282-8:2018 (EN 16282-8:2017) |
Equipment for commercial kitchens - Components for ventilation in commercial kitchens - Part 8: Installations for treatment of aerosol; Requirements and testing |
- |
Sì 08/03/2018
|
|
|
00156223 |
UNI EN 13141-3:2018 (EN 13141-3:2017) |
Ventilation for buildings - Performance testing of components/products for residential ventilation - Part 3: Range hoods for residential use without fan |
- |
Sì 08/03/2018
|
|
|
00156225 |
UNI EN 16798-5-2:2018 (EN 16798-5-2:2017) |
Energy performance of buildings - Ventilation for buildings - Part 5-2: Calculation methods for energy requirements of ventilation systems (Modules M5-6, M5-8, M6-5, M6-8, M7-5, M7-8) - Method 2: Distribution and generation |
- |
Sì 08/03/2018
|
|
|
00156226 |
UNI EN 14134:2019 |
Ventilation for buildings - Performance measurement and checks for residential ventilation systems |
- |
Sì 13/06/2019
|
|
|
00156227 |
UNI EN 13141-1:2019 |
Ventilation for buildings - Performance testing of components/products for residential ventilation - Part 1: Externally and internally mounted air transfer devices |
- |
Sì 07/03/2019
|
|
|
00156228 |
UNI EN 13141-5:2021 (EN 13141-5:2020) |
Ventilation for buildings - Performance testing of components/products for residential ventilation - Part 5: Cowls, assisted cowls and roof outlet terminal devices |
- |
Sì 04/02/2021
|
|
|
00156230 |
UNI EN 13053:2020 (EN 13053:2019) |
Ventilation for buildings - Air handling units - Rating and performance for units, components and sections |
- |
Sì 27/03/2020
|
|
|
00156235 |
EN ISO 12759-4:2019 |
Fans - Efficiency classification for fans - Part 4: Driven fans at maximum operating speed (ISO 12759-4:2019)
|
- |
Prossima
|
|
|
00156236 |
UNI EN ISO 12759-5:2022 |
Fans - Efficiency classification for fans - Part 5: Jet fans (ISO 12759-5:2021) |
- |
Sì 24/03/2022
|
|
|
00156231 |
UNI CEN/TS 16244:2018 |
Ventilation in hospitals - Coherent hierarchic structure and common terms and definitions for a standard related to ventilation in hospitals |
- |
Sì 31/07/2018
|
|
|
Codice progetto |
Codice Norma |
Titolo |
Sommario |
Pubblicazione UNI |
|
|
00156238 |
UNI CEN/TS 17153:2018 |
Ventilation for buildings - Correction of air flow rate according to ambient conditions |
- |
Sì 08/11/2018
|
|
|
00156179 |
UNI EN 17192:2019 (EN 17192:2018) |
Ventilation for buildings - Ductwork - Non-metallic ductwork - Requirements and test methods |
- |
Sì 07/03/2019
|
|
|
00156247 |
UNI EN 13142:2021 |
Ventilation for buildings - Components/products for residential ventilation - Required and optional performance characteristics |
- |
Sì 30/09/2021
|
|
|
00156248 |
UNI EN 13141-4:2021 |
Ventilation for buildings - Performance testing of components/products for residential ventilation - Part 4: Aerodynamic, electrical power and acoustic performance of unidirectional ventilation units |
- |
Sì 30/09/2021
|
|
|
00156249 |
UNI EN 13141-7:2021 |
Ventilation for buildings - Performance testing of components/products for residential ventilation - Part 7: Performance testing of ducted mechanical supply and exhaust ventilation units (including heat recovery) |
- |
Sì 30/09/2021
|
|
|
00156250 |
UNI EN 13141-8:2022 |
Ventilation for buildings - Performance testing of components/products for residential ventilation - Part 8: Performance testing of non-ducted mechanical supply and exhaust ventilation units (including heat recovery) |
- |
Sì 27/10/2022
|
|
|
00156270 |
UNI EN 16282-7:2021 (EN 16282-7:2017+A1:2021) |
Equipment for commercial kitchens - Components for ventilation in commercial kitchens - Part 7: Installation and use of fixed fire suppression systems |
- |
Sì 30/09/2021
|
|
|
00156271 |
UNI EN 16282-3:2021 (EN 16282-3:2016+A1:2021) |
Equipment for commercial kitchens - Components for ventilation in commercial kitchens - Part 3: Kitchen ventilation ceilings; design and safety requirements |
- |
Sì 30/09/2021
|
|
|
00156274 |
UNI EN ISO 13349-1:2023 |
Fans - Vocabulary and definitions of categories - Part 1: Vocabulary (ISO 13349-1:2022) |
- |
Sì 31/03/2023
|
|
|
00156275 |
UNI EN ISO 13349-2:2023 |
Fans - Vocabulary and definitions of categories - Part 2: Categories (ISO 13349-2:2022) |
- |
Sì 30/03/2023
|
|
|
00156276 |
UNI EN 1751:2024 |
Ventilation for buildings - Air terminal devices - Aerodynamic testing of damper and valves |
- |
Sì 04/07/2024
|
|
|
00156269 |
EN 16211:2024 |
Ventilation for buildings - Measurement of air flow rates on site - Methods
|
- |
Prossima
|
|
|
00156288 |
UNI EN ISO 13351:2024 |
Fans - Dimensions (ISO 13351:2024)
|
- |
Sì 10/10/2024
|
|
|
00156160 |
UNI EN 15726:2011 |
Ventilation for buildings - Air diffusion - Measurements in the occupied zone of airconditioned/ventilated rooms to evaluate thermal and acoustic conditions |
This European Standard is applicable to measure some parameters of thermal and acoustic comfort (i.e. temperatures, air velocities…) in a room with an air diffusion system. This European Standard can be used on site or in a lab for full-scale measurements. This European Standard applies to ventilation or air conditioning systems designed to maintain the comfort conditions in buildings. It is not applicable in the case of systems for the control of industrial or other special process environments.
|
Sì 26/10/2011
|
|
Codice progetto |
Codice Norma |
Titolo |
Sommario |
Pubblicazione UNI |
|
00156053 |
EN 13053:2001 |
Ventilation for buildings. Air handling units. Rating and performance for units, components and sections |
This standard specifies requirements and testing for ratings and performance of air hanling units as a whole. |
Non prevista
|
|
00156069 |
EN 13141-5:2004 |
Ventilation for buildings - Performance testing of components/products for residential ventilation - Part 5: Cowls and roof outlet terminal devices |
This European standard specifies methods for measuring the aerodynamic and acoustic characteristics of cowls and roof outlets used in both natural and mechanical ventilation. Only those cowls and roof outlets fitted onto ducts which project above the roof surface are covered. |
Non prevista
|
|
00156030 |
EN 13141-1:2004 |
Ventilation for buildings - Performance testing of components/products for residential ventilation - Part 1: Externally and internally mounted air transfer devices |
This European standard specifies laboratory methods for testing externally and internally mounted air transfer devices operating under pressure differences. It applies to any devices located between two spaces (between one room and outside, or between two rooms) such as: - devices with fixed opening(s); - devices with manually adjustable opening(s); - devices with pressure difference controlled opening(s). It describes tests intended to characterize the following: - flowrate/pressure; - air diffusion; - air leakage (for closeable externally mounted air transfer device); - sound reduction;... |
Non prevista
|
|
00156066 |
EN 13141-2:2004 |
Ventilation for buildings - Performance testing of components/products for residential ventilation - Part 2: Exhaust and supply air terminal devices |
This European Standard specifies laboratory methods for testing flowrate and noise production of exhaust and supply air terminal devices operating under pressure differences. It applies to devices used in mechanical systems and passive stack systems. The device may be one of the following - device with a manually adjustable opening or, - device with a fixed opening or, - pressure difference controlled device. |
Non prevista
|
|
00156067 |
EN 13141-3:2004 |
Ventilation for buildings - Performance testing of components/products for residential ventilation - Part 3: Range hoods for residential use |
This European standard specifies methods for measuring the main performance characteristics of range hoods for residential use. It applies to recirculating range hoods, air extraction range hoods incorporating a fan and air extraction range hoods without fan. This standard does not specify values for performance characteristics. Safety Requirements are specified in EN 60335-2-31. |
Non prevista
|
|
00156068 |
EN 13141-4:2004 |
Ventilation for buildings - Performance testing of components/products for residential ventilation - Part 4: Fans used in residential ventilation systems |
This European standard specifies performance test methods for fans used in the residential ventilation. These methods primarily concern: a) Ventilation fans installed on a wall or in a window without any duct; b) Ventilation fans installed in the downstream of a duct; c) Ventilation fans installed in the upwardstream of a duct; d) Ventilation fans installed in a duct; e) Encased fans having several inlets. This standard defines for each type of fan, the acoustic testing methods. The following method can be used: a) In duct method; b) Reverberant field method; c) Free field or semi-reverberant method. |
Non prevista
|
|
00156070 |
EN 13141-6:2004 |
Ventilation for buildings - Performance testing of components/products for residential ventilation - Part 6: Exhaust ventilation system packages used in a single dwelling |
This European standard specifies laboratory methods for measuring the aerodynamic and acoustic performance characteristics and energy consumption of assembled exhaust ventilation system packages for single dwelling. The object of this standard is to provide tested characteristics for a system package in extreme conditions to enable the user to be assured that the same values will be achieved on site when the system package is installed in accordance with the manufacturer's instruction and within these limits of the test conditions. |
Non prevista
|
|
00156075 |
EN 13141-7:2004 |
Ventilation for buildings. Performance testing of components/products for residential ventilation. P. 7 Performance testing of a mechanical supply and exhaust ventil. units for mech. Ventil. syst. intended for single family dwell. |
This part of prEN xxxxx specifies the laboratory test methods and test requirements for testing of Aerodynamic, Thermal and Acoustic performances, and Electrical Power of a mechanical Supply and Exhaust ventilation unit used in a single dwelling. In general such a unit contains: - supply and exhaust air fans, - air filters, - air to air heat exchanger with/without air to air heat pump for exhaust air heat recovery, - control system. Such equipement can be provided in more than one assembly, the separate assemblies of which are designed to be used together. |
Non prevista
|
|
00156033 |
EN 13465:2004 |
Ventilation for buildings - Calculation methods for the determination of air flow rates in dwellings |
This Standard specifies methods to calculate basic whole house air flow rates for single family houses and individual apartments up to the size of approximately 1 000 m3, to be used for applications such as energy loss calculations, heat load calculations and indoor air quality evaluations. The same basic methods apply for these different applications, the input parameter values being selected according to the requirements of the specific application. |
Non prevista
|
|
00156032 |
EN 14134:2004 |
Ventilation for buildings - Performance testing and installation checks of residential ventilation systems |
This European Standard specifies checks and test methods in order to verify the fitness for purpose of installed ventilation systems in dwellings. It can be applied to commissioning of new systems and performance testing of existing systems. The standard enables the choice between simple test methods, when sufficient, and extensive measurements, when necessary. The standard applies to mechanical and non-mechanical (natural) ventilation systems comprising any of the following: - passive stack ventilation ducts, - air terminal devices (supply, exhaust), etc. |
Non prevista
|
|
00156031 |
EN 13142:2004 |
Ventilation for buildings - Components/products for residential ventilation - Required and optional performance characteristics |
This European Standard specifies the component/product performance characteristics which may be necessary for the design and dimensioning of residential ventilation systems to ensure the predetermined comfort conditions of temperature, air velocity, humidity and sound in the occupied zone. It defines those performance characteristics which shall be measured and presented according to relevant test methods, and other performance characteristics which are optional but which may be required, e.g. to comply with local or national regulations. |
Non prevista
|
|
00156057 |
EN 13779:2004 |
Ventilation for non residential buildings. Performance requirements for ventilation and air-conditioning systems |
This document applies to the design of ventilation, air-conditioning and room-conditioning systems for non-residential buildings subject to human occupancy. It focuses on the definitions of the various parameters that are relevant for HVAC-Systems. The various levels of classification given have no normative value and can be adapted to specific National Regulations or agreements. |
Non prevista
|
|
00156088 |
EN 13053:2006 |
Ventilation for buildings - Air handling units - Rating and performance for units, components and sections |
This European Standard specifies requirements and testing for ratings and performance of air handling units as a whole.It also specifies requirements, classification, and testing of specific components and sections of air handling units. For many components and sections it refers to component standards, but it also specifies restrictions or applications of standards developed for standalone components.This standard is applicable both to standardized designs, which may be in a range of sizes having common construction concepts, and also to custom-design units. It also applies both to air handling units, which are completely prefabricated, and to units which are built up on site. Generally the units within the scope of this standard include at least a fan, a heat exchanger and an air filter.This standard is not applicable to the following:a) air conditioning units serving a limited area in a building, such as fan coil units;b) units for residential buildings;c) units producing ventilation air mainly for a manufacturing process. |
Non prevista
|
|
00156078 |
EN 15241:2007 |
Ventilation for buildings - Calculation methods for energy losses due to ventilation and infiltration in commercial buildings |
This European standard describes the method to calculate the energy impact of ventilation systems (including airing) in buildings to be used for applications such as energy calculations, heat and cooling load calculation. It purpose is to define how to calculate the characteristics (temperature , humidity) of the air entering the building,
and the corresponding energies required for its treatment as the auxiliaries electrical energy required. |
Non prevista
|
|
00156100 |
EN 15251:2007 |
Indoor environmental input parameters for design and assessment of energy performance of buildings addressing indoor air quality, thermal environment, lighting and acoustics |
This European Standard specifies the criteria for indoor environment and how they are used to meet the requirements in the EPBD.
òThe standard specify how to establish indoor environmental input parameters for the energy performance calculations.
òThe standard also specify methods for long term evaluation of the obtained indoor environment as a result of calculations or measurements. (summer overheating)
òThe standard specifies how different categories of indoor environment can be used.
òThe standard do not require certain criteria to be used. This is up to national or individual project specifications.
òThe standard includes a special section for natural ventilated buildings without mechanical cooling.
òThe standard specifies criteria for measurements to be used by inspection or monitoring of the indoor
environment in existing buildings. |
Non prevista
|
|
00156130 |
EN ISO 5801:2008 |
Industrial fans - Performance testing using standardized airways (ISO 5801:2007 including Cor 1:2008) |
This European Standard deals with the determination of the performance of industrial fans of all types except those designed solely for air circulation e.g. ceiling fans and table fans. |
Non prevista
|
|
00156134 |
EN ISO 13350:2008 |
Industrial fans - Performance testing of jet fans (ISO 13350:1999) |
This International Standard deals with the determination of those technical characteristics needed to describe all aspects of the performance of jet fans as defined in ISO 13349. It does not cover those fans designed for ducted applications, nor those designed solely for air circulation, e.g. ceiling fans and table fans. The test procedures described in this International Standard relate to laboratory conditions. The measurement of performance under on-site conditions is not included. |
Non prevista
|
|
00156135 |
EN ISO 13351:2008 |
Industrial fans - Dimensions (ISO 13351:1996) |
This European Standard specifies size designations for industrial fans and specifies dimensions for the circular and rectangular flanges of general purpose industrial fans. It does not apply to cross-flow fans, or fan appliances used for household or similar applications. |
Non prevista
|
|
00156136 |
EN 13141-7:2010 |
Ventilation for buildings - Performance of testing components/products for residential ventilation - Part 7: Performance testing of a mechanical supply and exhaust ventilation units (including heat recovery) for mechanical ventilation systems intended for single family dwellings |
This part of EN 13141 specifies the laboratory test methods and test requirements for the testing of aerodynamic, thermal and acoustic performance, and the electrical power of a mechanical supply and exhaust ventilation unit used in a single dwelling. It covers unit that contain at least, within one or more casing: - supply and exhaust air fans; - air filters - air-to-air heat exchanger and/or Exhaust Air-to-Outdoor Air heat pump for exhaust air heat recovery; - control system. Such equipment can be provided in more than one assembly, the separate assemblies of which are designed to be used together. The different possible arrangements of heat recovery heat exchangers and/or heat pumps are described in Annex A. This standard does not deal with non-ducted units. This standard does not deal with collective units (centralised or semi-centralised systems) This standard does not cover ventilation systems that may also provide and water space heating and hot water production This standard does not cover units including combustion engine driven compression heat pumps and absorption heat pump. Electrical safety requirements are given in EN 60335-2-40 and EN 60335-2-80. |
Non prevista
|
|
00156132 |
EN ISO 5802:2008 |
Industrial fans - Performance testing in situ (ISO 5802:2001) |
This European Standard specifies tests for determining one or more performance characteristics of fans installed in an operational circuit when handling a monophase fluid. |
Non prevista
|
|
Codice progetto |
Codice Norma |
Titolo |
Sommario |
Pubblicazione UNI |
|
00156133 |
EN ISO 13349:2008 |
Industrial fans - Vocabulary and definitions of categories (ISO 13349:1999) |
This European Standard provides a vocabulary and defines categories for general purpose industrial fans and their component parts. It is applicable to any fan used for industrial purposes, including the ventilation of buildings and mines, but excluding ceiling, pedestal and similar circulation types of fans such as those commonly used for non-industrial purposes. |
Non prevista
|
|
00156144 |
EN ISO 13351:2009 |
Fans - Dimensions (ISO/FDIS 13351:2009) |
This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and shall not be referred to as a European Standard. |
Non prevista
|
|
00156148 |
UNI EN 13141-4:2011 |
Ventilation for buildings - Performance testing of components/products for residential ventilation - Part 4: Fans used in residential ventilation systems |
This European Standard specifies aerodynamic, acoustic and electrical power performance test methods for fans used in residential ventilation. These methods primarily concern: - ventilation fans installed on a wall or in a window without any duct; - ventilation fans installed in the downstream of a duct; - ventilation fans installed in the upstream of a duct; - ventilation fans installed in a duct; - encased ventilation fans having several inlets. For acoustic performance testing one of the following methods is be used: - in duct method; - reverberant field method; - free field or semi-reverberant method. |
Non prevista
|
|
00156157 |
EN 13053:2006/FprA1 |
Ventilation for buildings - Air handling units - Rating and performance for units, components and sections
|
To amend EN to address issues regarding energy classification of Air Handling Units as a result of discussions in Eurovent WG6C. |
Non prevista
|
|
00156159 |
UNI EN 1751:2014 |
Ventilation for buildings - Air terminal devices - Aerodynamic testing of damper and valves |
This European Standard specifies methods for the testing and rating of dampers and valves used in air distribution systems with pressure differences up to 2000 Pa. |
Non prevista
|
|
00156164 |
UNI EN 13141-8:2014 |
Ventilation for buildings - Performance testing of components/products for residential ventilation - Part 8: Performance testing of un-ducted mechanical supply and exhaust ventilation units (including heat recovery) for mechanical ventilation systems intended for a single room |
This part of EN 13141 specifies the laboratory test methods and test requirements for the testing of un-ducted mechanical supply and exhaust ventilation units (including heat recovery) for mechanical ventilation systems intended for a single room |
Non prevista
|
|
00156165 |
UNI EN 13053:2006+A1:2011 |
Ventilation for buildings - Air handling units - Rating and performance for units, components and sections |
To amend EN to address issues regarding energy classification of Air Handling Units as a result of discussions in Eurovent WG6C. |
Non prevista
|
|
00156169 |
UNI EN 13142:2013 |
Ventilation for buildings - Components/products for residential ventilation - Required and optional performance characteristics |
- |
Non prevista
|
|
00156185 |
UNI EN 16211:2015 |
Ventilation for buildings - Measurement of air flows on site - Methods |
- |
Non prevista
|
|
00156214 |
UNI EN 16282-3:2017 (EN 16282-3:2016) |
Equipment for commercial kitchens - Components for ventilation in commercial kitchens - Part 3: Kitchen ventilation ceilings; design and safety requirements |
- |
Non prevista
|
|
00156218 |
UNI EN 16282-7:2018 (EN 16282-7:2017) |
Equipment for commercial kitchens - Components for ventilation in commercial kitchens - Part 7: Installation and use of fixed fire suppression systems |
- |
Non prevista
|
|
