CT 221 - Progettazione e fabbricazione di attrezzature a pressione

00054025

EN 764-5:2002

Pressure equipment - Part 5: Compliance and inspection documentation of materials

This Part of this European Standard specifies the materials for pressure equipment to comply with the requirements of the relevant pressure equipment material specification. This Part describes how this shall be applied to materials intended for the manufacturing of pressure bearing parts and attachments to them.

Non prevista

00054044

EN 13445-3:2002/A8:2006

Unfired pressure vessels - Part 3: Design

Flat walls supported by stays, stay tubes and other reinforcing elements (only unstayed flat walls are now provided)

Non prevista

00054027

EN 13445-6:2002/A1:2004

Unfired pressure vessels - Part 6: Requirements for the design and fabrication of pressure vessels and pressure parts constructed from spheroidal graphite cast iron

Methodology for determining lifetime of SGCI under pulsating loads

Non prevista

00054022

EN 764-4:2002

Pressure equipment. Part 4: Establishment of technical delivery conditions for metallic materials

This Part of the European Standard specifies the requirements for the establishment of the technical delivery
conditions in form of:
- harmonized European Standard for material;
- European approval for material (EAM);
- particular material appraisal
for metallic materials for pressure equipment in all product forms, and is restricted to steel at present. Welding
consumables are not covered by this standard.

Non prevista

00054020

EN 764-2:2002

Pressure equipment. Part 2: Quantities, symbols and units

This European Standard specifies the basic quantities, symbols and units to be used for pressure equipment and
assemblies addressed by the European Directive 97/23/EC.

Non prevista

00054023

EN 764-1:2004

Pressure equipment - Terminology - Part 1: Pressure, temperature, volume, nominal size

This part of the European standard defines the basic terminology and symbols to be used for pressure equipment and assemblies addressed by the European Directive 97/23/EC with regard to pressure, temperature, volume and nominal size.NOTE 1 In addition to terms used in the three official CEN languages (English, French and German), this European standard gives in annex A the equivalent terms in the Czech, Danish, Dutch, Finnish, Greek, Icelandic, Italian, Norwegian, Portuguese, Spanish, and Swedish languages; these are published under the respon-sibility of the respective member bodies for those countries. However, only the terms and definitions given in the official languages can be considered as EN terms and definitions. NOTE 2This part of the European standard does not stipulate the units to be used for the quantities defined. These shall be taken from the other parts of the standard.

Non prevista

00054029

EN 13445-5:2002

Unfired pressure vessels. Part 5: Inspection and testing

Scopo

Non prevista

00054058

EN 14359:2006

Gas-loaded accumulators for fluid power applications

This European Standard specifies the requirements for materials, design, manufacture, testing, inspection, safety systems and documentation for commonly used types of gas-loaded accumulators for fluid power applications up to being placed on the market. It includes interconnected pressure vessels or 'gas bottles' used to provide additional gas capacity and communicating with the gas chamber of the accumulator by means of a pipe connection.
This European Standard applies to the following components, defined as the pressure containing envelope of gas-loaded accumulators. They consist of one or several parts joined together by a variety of mechanical means including welding:

Non prevista

00054028

EN 13445-8:2006

Unfired pressure vessels - Part 8 : Additional requirements for pressure vessels of aluminium and aluminium alloys

This Part 8 of this European Standard specifies requirements for unfired pressure vessels and their parts made of aluminium and aluminium alloys in addition to the general requirements for unfired pressure ves-sels under EN 13445:2002 Parts 1 to 5. This European Standard specifies unfired pressure vessels for loads up to 500 full cycles.

Non prevista

00054042

EN 13445-3:2002/A6:2006

Unfired pressure vessels - Part 3: Design - Clause 10 'Flat Ends'

Design method for flat ends when fatigue is not the controlling factor; the present method in Clause 10 makes no distinction and may may be too conservative in these cases.

Non prevista

00054041

EN 13445-3:2002/A5:2006

Unfired pressure vessels - Part 3: Design - Clause 9 'opening in shells'

Design method for openings when fatigue is not the controlling factor; the present method in Clause 9 makes no distinction and may be too conservative in these cases.

Non prevista

00054048

EN 13445-5:2002/A2:2005

Unfired pressure vessels - Part 5: Inspection and testing

To define the pressure for the proof test more precisely and to determine additional requirements to obtain an equivalent level of safety when the test pressure has to be reduced on account of a weak component

Non prevista

00054063

EN 13445-5:2002/A5:2006

Unfired pressure vessels - Part 5: Inspection and testing

Amendment to Non-destructive testing requirements

Non prevista

00054049

13445-5:2002/A3:2006

Unfired pressure vessels - Part 5: Inspection and testing

NDT of specific welds in particular single run welds from one or both sides which are currently used for smaller pressure vessels. Additional requirements are necessary in addition to those for multi- layer welds of V1

Non prevista

00054062

UNI EN 13445-3:2019 (EN 13445-3:2014/A6:2019

Unfired pressure vessels – Part 3: Design

Annex J for tubesheets amendment

Non prevista

00054064

UNI EN 13445-3:2019 (EN 13445-3:2014/A5:2018)

Unfired pressure vessels – Part 3: Design

Clauses 17 & 18 for fatigue amendment

Non prevista

00054066

UNI EN 13445-5:2009/A2:2011

Unfired pressure vessels – Part 5: Inspection and testing

Amendment for serially produced vessels

Non prevista

00054055

EN 13445-3:2002/A11:2006

Unfired pressure vessels - Part 3: Design

Modifications to Clause 2, 5.4, 5.7, Annex A, Annex B and Annex ZA.

Non prevista

00054057

EN 13445-5:2002/A4:2006

Unfired pressure vessels - Part 5: Inspection and testing

Delete the third paragraph: This Part does not give inspection and testing provisions for vessels designed using Design by Analysis - Direct Route (DBA) of EN 13445-3:2002 Annex B. Modification to Clause 1, Clause 2, 5.2.1, 6.6.1, A.1 and Annex ZA

Non prevista

00054038

EN 13445-3:2002/A2:2007

Unfired pressure vessels - Part 3: Design

Static design by experimental methods.Design by experimental methods as an alternative to Design By Analysis and Design By Formulae (bursting and strain gauge testing)

Non prevista

00054039

EN 13445-3:2002/A3:2007

Unfired pressure vessels - Part 3: Design

Design by formula (alternative design factor).Alternative Design By Formulae method considering a reduced safety factor on tensile strength in order to reduce thicknesses (the so called Alternative Route)

Non prevista

00054076

EN 13445-3:2002/A17:2007

Unfired pressure vessels - Part 3: Design

The amendment refers to complex editorial changes to the layout of Annex J for tubesheets.

Non prevista

00054052

EN 13445-3:2002/A1:2007

Unfired pressure vessels - Part 3: Design

The amendment refers to additional requirements for creep

Non prevista

00054032

EN 13445-2:2002/A1:2007

Unfired pressure vessels - Part 2: Materials

The amendment refers to additional requirements for creep

Non prevista

00054072

EN 13445-1:2002/A3:2007

Unfired pressure vessels - Part 1: General -

To provide better and more detailed explanation in EN 13445-1 of the other parts of the EN 13445 series.

Non prevista

00054031

EN 13445-1:2002/A1:2007

Unfired pressure vessels - Part 1: General

The amendment refers to additional requirements for creep, in particular specific changes in introduction, scope, definitions, symbols and Annex ZA

Non prevista

00054040

EN 13445-3:2002/A4:2005

Unfired pressure vessels - Part 3: Design

Reinforced and toroidal bellows. Reinforced and toroidal bellows in fixed tubesheet Heat Exchangers (only bellows having flat walls are considered now in Clause 14)

Non prevista

00054034

EN 13445-5:2002/A1:2007

Unfired pressure vessels - Part 5 : Inspection & testing

The amendment refers to additional requirements for creep

Non prevista

00054090

UNI EN 13445-2:2009/A2:2012

Unfired pressure vessels - Part 2: Materials

Update of Table B.2-12

Non prevista

00054084

EN 15776:2011

Unfired pressure vessels - Additional requirements for the design and fabrication of pressure vessels and parts constructed from cast iron with elongation equal or less than 15%

This European standard specifies requirements for the design, material, manufacturing and testing of pressure vessels and pressure vessel parts. The allowed materials are specific grades with an elongation equal or less than 15%

Non prevista

00054047

EN 13445-6:2002/A2:2006

Unfired pressure vessels - Part 6: Requirements for the design and fabrication of pressure vessels and pressure parts constructed from spheroidal graphite cast iron

This European Standard specifies requirements for the design, materials, manufacturing and testing of pressure vessels and pressure vessel parts intended for use with a maximum allowable pressure, PS, equal or less than 100 bar and shell wall thicknesses not exceeding 60 mm, which are constructed of ferritic or austenitic spheroidal graphite cast iron. The thickness limitation of the shell does not apply to the thickness of flanges, reinforcements, bosses, etc.
NOTE1 Austenitic spheroidal graphite cast iron grades are principally used for high and low temperature applications and their corrosion resistance properties.
NOTE2 The allowable grades of spheroidal graphite cast iron are listed in Tables 3 and 4Service conditions are given in clause 4.
NOTE3 The allowable grades do not include lamellar graphite cast iron grades, which are explicitly excluded from this standard because of low elongation and brittle material behaviour, which requires the use of different safety factors and a different approach.

Non prevista

00054073

CEN/TR 13445-9:2007

Unfired pressure vessels - Part 9: Conformance of the EN 13445 series to ISO 16528

This edition is limited to vessels of steel construction, but will be amended later to include spheroidal graphite cast iron and aluminium.

Non prevista

00054059

EN 13445-3:2002/A10:2008

Unfired pressure vessels - Part 3: Design

This Part of this European Standard specifies requirements for the design of unfired pressure vessels covered by EN 13445-1:2002 and constructed of steels in accordance with EN 13445-2:2002.

Non prevista

00054083

EN 13445-5:2002/A10:2008

Unfired pressure vessels — Part 5: Inspection and testing

This part of this European Standard specifies the inspectionand testing of individual and serially produced pressure vessels made of steels in accordance with EN 13445-2 subject to predominantly non-cyclic operation (i.e. vessels operating below 500 full equivalent pressure cycles).

Non prevista

00054053

EN 13445-1:2002/A2:2006

Unfired pressure vessels - Part 1: General

Delete: However Parts 2, 4 and 5 of this edition of the standard do not include provision within their respective areas of responsibility for vessels designed using Design by Analysis - Direct Route (DBA) of EN 13445-3:2002, Annex B. Replace old Annex ZA with new one.

Non prevista

00054014

EN 13445-4:2002

Unfired pressure vessels. Part 4: Fabrication

This document specifies requirements for the manufacture of unfired pressure vessels and their parts, made of steels, including their connections to non-pressure parts. It specifies requirements for material traceability, manufacturing tolerances, welding requirements, production tests, forming requirements, heat treatment, repairs and finishing operations. This document does not give provisions for manufacturing requirements for vessels designed using Design by Analysis - Direct Route (DBA) of Annex B of EN 13445-3:2002.

Non prevista

00054013

EN 13445-3:2002

Unfired pressure vessels. Part 3: Design

This part of this European Standard specifies requirements for the design of unfired pressure vessels covered by EN 13445-1 and constructed of steels in accordance with EN 13445-2. Annex C of EN 13445-5 specifies requirements for the design of access and inspection openings, closing mechanisms and special locking elements.

Non prevista

00054007

EN 13445-1:2002

Unfired pressure vessels.Part 1: General

EN 13445 specifies the requiremente for design, construction, inspection and testing of unfired pressure vessels. This part outlines the basic principles underpinning the standard.

Non prevista

00054012

EN 13445-2:2002

Unfired pressure vessels.Part 2: Materials

This Part of this European Standard specifies the requirements for materials (including clad materials) for unfired pressure vessels manufactured from metallic materials; it is currently limited to steels with sufficient ductility.

Non prevista

00054054

EN 13445-2:2002/A2:2006

Unfired pressure vessels - Part 2: Materials

Delete: This Part of the European Standard does not give provisions for material requirements and material selection for vessels designed using Design by Analysis - Direct Route (DBA) of EN 13445-3:2002, Annex B. Modifications to Clause1, Clause 2, Annex A, B.1 and Annex ZA.

Non prevista

00054068

EN 13445-2:2002/A5:2009

Unfired pressure vessels - Part 2: Materials

This part of this European Standard specifies the requirements for materials (including clad materials) for unfired pressure vessels and supports which are covered by EN 13445-1 and manufactured from metallic materials; it is currently limited to steels whit sufficient ductility. This document is not applicable in the creep range.

Non prevista

00054075

EN 13445-6:2002/A3:2008

Unfired pressure vessels — Part 6: Requirements for the design and fabrication of pressure vessels and pressure parts constructed from spheroidal graphite cast iron

This European Standard specifies requirements for the design, materials, manufacturing and testing of pressure vessels and pressure vessel parts intended for use with a maximum allowable pressure, PS, equal or less than 100 bar and shell wall thicknesses not exceeding 60 mm, which are constructed of ferritic or austenitic spheroidal graphite cast iron. The thickness limitation of the shell does not apply to the thickness of flanges, reinforcements, bosses, etc.

Non prevista

00054056

EN 13445-4:2002/A2:2006

Unfired pressure vessels - Part 4: Fabrication

Delete This document does not give provisions for manufacturing requirements for vessels designed using Design by Analysis - Direct Route (DBA) of Annex B of EN 13445-3:2002. Modifications to Clause 1, 5.4.4, 6.2, 8.1, 8.2, 9.3.1, 9.4.1, Clause 10 and Annex ZA.

Non prevista

00054069

EN 13445-4:2002/A3:2009

Unfired pressure vessels - Part 4: Fabrication

This document specifies requirements for the manufacture of unfired pressure vessels and their parts, made of steels, including their connections to non-pressure parts. It specifies requirements for material traceability, manufacturing tolerances, welding requirements, production tests, forming requirements, heat treatment, repairs and finishing operations. This document does not give provisions for manufacturing requirements for vessels designed using Design by Analysis - Direct Route (DBA) of Annex B of EN 13445-3.

Non prevista

00054060

EN 13445-2:2002/A3:2009

Unfired pressure vessels - Part 2: Materials

This Part of this European Standard specifies the requirements for materials (including clad materials) for unfired pressure vessels and supports which are covered by EN 13445-1 and manufactured from metallic materials; it is currently limited to steels with sufficient ductility. This document is not applicable in the creep range

Non prevista

00054071

EN 13445-3:2002/A16:2008

Unfired pressure vessels - Part 3: Design

This Part of this European Standard specifies requirements for the design of unfired pressure vessels covered by EN 13445-1:2002 and constructed of steels in accordance with EN 13445-2:2002.

Non prevista

00054093

EN 13445-4:2002/A5:2009

Unfired pressure vessels - Part 4: Fabrication

This document specifies requirements for the manufacture of unfired pressure vessels and their parts, made of steels, including their connections to non-pressure parts. It specifies requirements for material traceability, manufacturing tolerances, welding requirements, production tests, forming requirements, heat treatment, repairs and finishing operations. This document does not give provisions for manufacturing requirements for vessels designed using Design by Analysis - Direct Route (DBA) of Annex B of EN 13445-3.

Non prevista

00054092

UNI EN 13445-4:2009/A1:2011

Unfired pressure vessels - Part 4: Fabrication

Text is not available

Non prevista

00054097

UNI EN 13445-1:2009

Unfired pressure vessels - Part 1: General

This part of this European Standard defines the terms, definitions, quantities, symbols and units that are used throughout the EN 13445. It also contains instructions on how to use the standard (Annex A) as well as an index which covers the whole standard (Annex B). This information is aimed to aid the user of the EN 13445. This European Standard applies to unfired pressure vessels with a maximum allowable pressure greater than 0,5 bar gauge but may be used for vessels operating at lower pressures, including vacuum.
NOTE The selection, application and installation of safety related accessories intended to protect pressure vessels during operation are covered in EN 764-7.

Non prevista

00054098

UNI EN 13445-2:2009

Unfired pressure vessels - Part 2: Materials

This Part of this European Standard specifies the requirements for materials (including clad materials) for unfired pressure vessels and supports which are covered by EN 13445-1 and manufactured from metallic materials; it is currently limited to steels with sufficient ductility but it is, for components operating in the creep range, also limited to sufficiently creep ductile materials. It specifies the requirements for the selection, inspection, testing and marking of metallic materials for the fabrication of unfired pressure vessels.

Non prevista

00054099

EN 13445-3:2009

Unfired pressure vessels - Part 3: Design

This part of this European Standard specifies requirements for the design of unfired pressure vessels covered by EN 13445-1 and constructed of steels in accordance with EN 13445-2. Annex C of EN 13445-5 specifies requirements for the design of access and inspection openings, closing mechanisms and special locking elements.
NOTE This Part applies to design of vessels before putting into service. It may be used for in service calculation or analysis subject to appropriate adjustment.

Non prevista

00054100

EN 13445-4:2009

Unfired pressure vessels - Part 4: Fabrication

This Part of this European Standard specifies requirements for the manufacture of unfired pressure vessels and their parts, made of steels, including their connections to non-pressure parts. It specifies requirements for material traceability, manufacturing tolerances, welding requirements, production tests, forming requirements, heat treatment, repairs and finishing operations.

Non prevista

00054101

EN 13445-5:2009

Unfired pressure vessels - Part 5: Inspection and testing

This Part of this European Standard specifies the inspection and testing of individual and serially produced pressure vessels made of steels in accordance with EN 13445-2:2009 subject to predominantly non_cyclic operation (i.e. vessels operating below 500 full equivalent pressure cycles). Special provisions for cyclic operation are given in EN 13445-3:2009 and in Annex G of this Part. Special provisions for vessels or vessel parts working in the creep range are given in Clause 5, Clause 6, Clause 10, Annex H and Annex I of this Part.
NOTE The responsibilities of parties involved in the conformity assessment procedures are given in Directive 97/23/EC. Guidance on this can be found in CR 13445-7.

Non prevista

00054102

EN 13445-6:2009

Unfired pressure vessels - Part 6: Requirements for the design and fabrication of pressure vessels and pressure parts constructed from spheroidal graphite cast iron

This part of European Standard specifies requirements for the design, materials, manufacturing and testing of pressure vessels and pressure vessel parts intended for use with a maximum allowable pressure, PS, equal or less than 100 bar and shell wall thicknesses not exceeding 60 mm, which are constructed of ferritic or austenitic spheroidal graphite cast iron. The thickness limitation of the shell does not apply to thickness of flanges, reinforcements, bosses etc.
The allowable grades do not include lamellar graphite cast iron grades for ferritic and ustenitic grades, which are explicitly excluded from this European Standard because of low elongation and brittle material behaviour, which requires the use of different safety factors and a different approach.
NOTE 1 Austenitic spheroidal graphite cast iron grades are principally used for high and low temperature applications and for their corrosion resistance properties.
NOTE 2 The allowable grades of spheroidal graphite cast iron are listed in Tables 3 and 4. Service conditions are given in Clause 4.

Non prevista

00054103

EN 13445-8:2009

Unfired pressure vessels - Part 8: Additional requirements for pressure vessels of aluminium and aluminium alloys

This Part 8 of this European Standard specifies requirements for unfired pressure vessels and their parts made of aluminium and aluminium alloys in addition to the general requirements for unfired pressure vessels under EN 13445:2009 Parts 1 to 5. This European Standard specifies unfired pressure vessels for loads up to 500 full cycles.
NOTE Cast materials are not included in this version. Details regarding cast materials will be subject to an amendment to or a revision of this European Standard.

Non prevista

00054104

UNI EN 13445-5:2009/A1:2011

Unfired pressure vessels - Part 5: Inspection and testing

Pressure test on a statistical basis.

Non prevista

00054107

UNI EN 13445-5:2009/A3:2011

Unfired pressure vessels - Part 5: Inspection and testing

Pneumatic pressure test

Non prevista

00054106

EN 13445-10:2015 (UNI EN 13445-10:2016)

Unfired pressure vessels - Part 10: Additional requirements for pressure vessels of nickel and nickel alloys

Specifies requirements for unfired pressure vessels and their parts made of nickel and nickel alloys.

Non prevista

00054118

EN 13445-4:2009/A2:2014 (UNI EN 13445-4:2014)

Unfired pressure vessels - Part 4: Fabrication

Approval of permanent joining without welding

Non prevista

00054117

UNI EN 13445-5:2009/A4:2013

Unfired pressure vessels - Part 5: Inspection and testing

This Part of this European Standard specifies the inspection and testing of individual and serially produced pressure vessels made of steels in accordance with EN 13445-2:2009. Special provisions for cyclic operation are given in Annex G of this Part. Special provisions for vessels or vessel parts working in the creep range are given in Annex F and Annex I of this Part. NOTE The responsibilities of parties involved in the conformity assessment procedures are given in Directive 97/23/EC. Guidance on this can be found in CR 13445-7.

Non prevista

00054122

EN 13445-8:2014+A1:2014 (UNI EN 13445-8:2015)

Unfired pressure vessels - Part 8: Additional requirements for pressure vessels of aluminium and aluminium alloys

-

Non prevista

00054123

EN 13445-3:2014/A1:2015 (UNI EN 13445-3:2016)

Unfired pressure vessels - Part 3: Design

-

Non prevista

00054124

EN 13445-6:2014/A1:2015 (UNI EN 13445-6:2016)

Unfired pressure vessels - Part 6: Requirements for the design and fabrication of pressure vessels and pressure parts constructed from spheroidal graphite cast iron

-

Non prevista

00054126

EN 13445-1:2009+A1:2013 (UNI EN 13445-1:2014)

Unfired pressure vessels - Part 1: General

-

Non prevista

00054133

EN 13445-1:2014+A1:2014 (UNI EN 13445-1:2015)

Unfired pressure vessels - Part 1: General

-

Non prevista

00054136

EN 13445-6:2014 (UNI EN 13445-6:2015)

Unfired pressure vessels - Part 6: Requirements for the design and fabrication of pressure vessels and pressure parts constructed from spheroidal graphite cast iron

-

Non prevista

00054137

EN 13445-8:2014 (UNI EN 13445-8:2015)

Unfired pressure vessels - Part 8: Additional requirements for pressure vessels of aluminium and aluminium alloys

-

Non prevista

00054138CN

CN - EN 13445-3:2014

CORRECTION NOTICE - Unfired pressure vessels - Part 3: Design

-

Non prevista

00054139

EN 13445-1:2014 (UNI EN 13445-1:2015)

Unfired pressure vessels - Part 1: General

-

Non prevista

00054140

EN 13445-2:2014 (UNI EN 13445-2:2015)

Unfired pressure vessels - Part 2: Materials

-

Non prevista

00054141

EN 13445-4:2014 (UNI EN 13445-4:2015)

Unfired pressure vessels - Part 4: Fabrication

-

Non prevista

00054142

UNI EN 13445-3:2017 (EN 13445-3:2014/A2:2016)

Unfired pressure vessels - Part 3: Design

-

Non prevista

00054145

UNI EN 13445-2:2017 (EN 13445-2:2014/A1:2016)

Unfired pressure vessels - Part 2: Materials

-

Non prevista

00054146

UNI EN 13445-3:2017 (EN 13445-3:2014/A3:2017)

Unfired pressure vessels - Part 3: Design

-

Non prevista

00054155

UNI EN 13445-4:2016 (EN 13445-4:2014/A1:2016)

Unfired pressure vessels - Part 4: Fabrication

-

Non prevista

00054156

UNI EN 13445-4:2023 (EN 13445-4:2021/A1:2023)

Unfired pressure vessels - Part 4: Fabrication

-

Non prevista

00054157

EN 764-1:2015/FprA1:2016

Pressure equipment - Part 1: Vocabulary

-

Non prevista

00054154

EN 15776:2011+A1:2015 (UNI EN 15776:2016)

Unfired pressure vessels - Requirements for the design and fabrication of pressure vessels and pressure parts constructed from cast iron with an elongation after fracture equal or less than 15 %

-

Non prevista

00054163

UNI EN 13445-1:2018 (EN 13445-1:2014/A2:2018)

Unfired pressure vessels - Part 1: General

-

Non prevista

00054082

EN 13445-3:2014/A7:2019

Unfired pressure vessels - Part 3: Design

-

Non prevista

00054141CN

CN - EN 13445-4:2014

CORRECTION NOTICE - Unfired pressure vessels - Part 4: Fabrication

-

Non prevista

00054138

EN 13445-3:2014 (UNI EN 13445-3:2015)

Unfired pressure vessels - Part 3: Design

-

Non prevista

00054140CN

CN - EN 13445-2:2014

CORRECTION NOTICE - Unfired pressure vessels - Part 2: Materials

-

Non prevista

00054139CN

CN - EN 13445-1:2014

CORRECTION NOTICE - Unfired pressure vessels - Part 1: General

-

Non prevista

00054160

UNI EN 13445-2:2018 (EN 13445-2:2014/A3:2018)

Unfired pressure vessels - Part 2: Materials

-

Non prevista

00054168

UNI EN 13445-5:2018 (EN 13445-5:2014/A1:2018

Unfired pressure vessels - Part 5: Inspection and testing

-

Non prevista

00054169

UNI EN 13445-6:2019 (EN 13445-6:2014/A2:2018)

Unfired pressure vessels - Part 6: Requirements for the design and fabrication of pressure vessels and pressure parts constructed from spheroidal graphite cast iron Active Published 60.60.0000

-

Non prevista

00054170

UNI EN 13445-3:2018 (EN 13445-3:2014/A4:2018)

Unfired pressure vessels - Part 3: Design

-

Non prevista

00054171

EN 13445-3:2014/A8:2019

Unfired pressure vessels - Part 3: Design

-

Non prevista

00054172

UNI EN 13445-2:2018 (EN 13445-2:2014/A2:2018)

Unfired pressure vessels - Part 2: Materials

-

Non prevista

00054194

UNI EN 13445-2:2021

Unfired pressure vessels - Part 2: Materials

-

Non prevista

00054196

UNI EN 13445-4:2021

Unfired pressure vessels - Part 4: Fabrication

-

Non prevista

00054202

UNI EN 13445-2:2023 (EN 13445-2:2021/A1:2023)

Unfired pressure vessels - Part 2: Materials

-

Non prevista

00054113

UNI EN 13445-2:2009/A1:2012

Unfired pressure vessels - Part 2: Materials

Specifies the requirements for materials (including clad materials) for unfired pressure vessels and supports which are covered by EN 13445-1 and manufactured from metallic materials; it is currently limited to steels with sufficient ductility. This document is not applicable in the creep range.

Non prevista

00054065

EN 13445-3:2009/A2:2013 (UNI EN 13445-3:2014)

Unfired pressure vessels – Part 3: Design

Clause 16 for nonpressure loads amendment

Non prevista

00054109

UNI EN 13445-3:2009/A1:2012

Unfired pressure vessels - Part 3: Design

Modifications to clauses 17 and 18

Non prevista