
|
Codice progetto |
Codice Norma |
Titolo |
Sommario |
Pubblicazione UNI |
|

|
00088043 |
EN 14706:2005 |
Thermal insulation products for building equipment and industrial installations - Determination of maximum service temperature |
This European Standard specifies the equipment and procedures for determining the maximum service temperature of flat insulation products. It is applicable to thermal insulating products. |
Sì
|
|

|
00088109 |
EN 13793:2003 |
Thermal insulating products for building applications - Determination of behaviour under cyclic loading |
This draft European Standard specifies equipment and procedures for determining behaviour of test specimens under cyclic loading conditions. It is applicable to thermal insulating products. The selection of the conditions of the test shall be derived from the specific requirements of the intended application. |
Sì
|
|

|
00088124 |
EN 13820:2003 |
Thermal insulating materials for building applications - Determination of organic content |
This European Standard specifies the equipment and procedures for determining the organic content of thermal insulating materials. The method is aimed at determining the organic content for products which are basically inorganic, i.e. products containing a low percentage of organic compounds and/or products with inorganic facings and/or coatings. |
Sì
|
|

|
00088111 |
EN 13499:2003 |
Thermal insulation products for buildings - External thermal insulation composite systems (ETICS) based on expanded polystyrene - Specification |
This European Standard specifies the requirements for factory made products for external thermal insulation composite systems (ETICS) based on expanded polystyrene, delivered as a kit, and used as thermal insulation for buildings.The standard describes product characteristics and includes procedures for testing, marking and labelling.ETICS are applied to external surfaces of new or existing walls and/or soffits to improve the thermal insulation. ETICS include special fittings (base profiles, corner profiles, etc.) to connect them to adjacent building structures (apertures, corners, parapets, etc.). ETICS give protection against weathering and improve the appearance of the buildings. They do not contribute the stability of the wall and/or soffits on which they are installed. The standard covers systems where the thermal insulation material is required for the load transfer to the substrate.This standard covers systems with a declared thermal resistance equal to or greater than 1 m¦xK/W.The requirements from national regulations concerning the mechanical resistance and stability of ETICS should be taken into account.This standard does not cover the strength between the ETICS and the building surface to which it shall be fixed, i. e. the substrate. |
Sì
|
|

|
00088112 |
EN 13500:2003 |
Thermal insulation products for buildings - External thermal insulation composite systems (ETICS) based on mineral wool - Specification |
This European Standard specifies the requirements for factory made products for external thermal insulation composite systems (ETICS) based on mineral wool, delivered as a kit, and used as thermal insulation for buildings.The standard describes product characteristics and includes procedures for testing, marking and labelling.ETICS are applied to external surfaces of new or existing walls and/or soffits to improve the thermal insulation. ETICS include special fittings (base profiles, corner profiles, etc.) to connect them to adjacent building structures (apertures, corners, parapets, etc.). ETICS give protection against weathering and improve the appearance of the buildings. They do not contribute the stability of the wall and/or soffits on which they are installed. The standard covers systems where the thermal insulation material is required for the load transfer to the substrate. This standard covers systems with a declared thermal resistance equal to or greater than 1 m¦xK/W. The requirements from national regulations concerning the mechanical resistance and stability of ETICS should be taken into account.This standard does not cover the strength between the ETICS and the building surface to which it shall be fixed, i. e. the substrate. |
Sì
|
|

|
00088094 |
EN 14317-1:2004 |
Thermal insulating products for buildings - In-situ thermal insulation formed from exfoliated vermiculite (EV) products - Part 1: Specification for bonded and loose-fill products before installation |
This European Standard specifies the requirements for exfoliated vermiculite products for in-situ installation in roofs, ceilings, walls and floors.This Part 1 of the standard is a specification for the insulation products before installation covering the five product types, Vermiculite Aggregate (EVA), Coated Vermiculite (EVC), Bitumen Coated Vermiculite (EVB), Hydrophobic Vermiculite (EVH) and Premixed Vermiculite (EVM).Part 1 of this European Standard describes the product characteristics and includes procedures for testing, evalua-tion of conformity, marking and labelling.This standard does not specify the required level of a given property to be achieved by a product to demonstrate fitness for purpose in a particular application. The levels required for a given application are to be found in regulations or non-conflicting standards.This European Standard does not cover factory made insulation products of formed shapes and boards made with exfoliated vermiculite.The products covered by this standard are not intended to be used primarily for airborne sound insulation or sound absorption applications although they may improve the performance of the buildings in these respects when installed for their primary thermal insulation intended use. |
Sì
|
|

|
00088057 |
EN 14063-1:2004 |
Thermal insulation products for buildings - In-situ formed expanded clay lightweight aggregate products - Part 1: Specification for the loose-fill products before installation |
This document covers insulation materials made from expanded clay lightweight aggregate to be formed in-situ. Examples of applications for these products are insulation for roofs, walls, ceilings etc. The main addressed characteristics will be: Thermal- and water vapour transmission, mechanical properties and behaviour under water exposure for the material being installed in accordance with the following parts of the standard. |
Sì
|
|

|
00088080 |
EN 13468:2001 |
Thermal insulating products for building equipment and industrial
installations - Determination of trace quantities of water soluble
chloride, fluoride, silicate, sodium ions and pH |
This standard specifies the equipment and procedures for determining trace quantities of the water
soluble chloride, fluoride, silicate and sodium ions in an aqueous extract of the product. It also describes
a procedure for the determination of the pH of the aqueous extract. The standard is applicable to thermal
insulating products.
NOTE The determination of these parameters may be relevant for thermal insulating products intended for
application to stainless austenitic steel surfaces. The presence of chloride, fluoride, silicate and sodium ions under
certain conditions may influence the risk of stress corrosion cracking. See informative annex B for further information. |
Sì
|
|

|
00088115 |
EN 13471:2001 |
Thermal insulating products for building equipment and industrial
installations - Determination of the coefficient of thermal
expansion |
This European Standard specifies the equipment and procedures for determining the coefficient of linear thermal expansion. The standard is applicable to thermal insulating products within the temperature range - 196 C to 850 C, subject to the possible temperature limitation of the test specimens. It shall not be used for products which during the test experience dimensional changes due to the loss of hydration
water or which undergo other phase changes. |
Sì
|
|

|
00088116 |
EN 13472:2001 |
Thermal insulating products for building equipment and industrial
installations - Determination of short term water absorption by
partial immersion of preformed pipe insulation |
This European Standard specifies the equipment and procedures for determining the short term water
absorption of preformed pipe insulation by partial immersion in water. It is applicable to thermal insulating
products.
NOTE It is intended to simulate the water absorption caused by exposure to rain for 24 h during product installation.
If the pipe insulation is cut from a flat product, then the short term water absorption by partial immersion
can be obtained from tests carried out on the flat product with similar properties in accordance with EN
1609, providing the test is carried out in the direction giving the highest water uptake. |
Sì
|
|

|
00088113 |
EN 13470:2001 |
Thermal insulating products for building equipment and industrial
installations - Determination of the apparent density of
preformed pipe insulation |
This European Standard specifies the equipment and procedures for determining the apparent overall density and the apparent core density under reference conditions. It is applicable to full size thermal insulating products and test specimens of preformed pipe insulation |
Sì
|
|

|
00088081 |
EN 13469:2001 |
Thermal insulating products for building equipment and industrial installations. Determination of water vapour transmission properties of preformed pipe insulation |
This standard specifies the equipment and procedure for determining the water vapour transmission properties of preformed pipe insulation |
Sì
|
|

|
00088061 |
EN 14316-1:2004 |
Thermal insulating products for buildings - In-situ thermal insulation formed from expanded perlite (EP) products - Part 1: Specification for bonded and loose-fill products before installation |
This European Standard specifies the requirements for expanded perlite products for in-situ installation in roofs, ceilings, walls and floors.This Part 1 of the standard is a specification for the insulation products before installation covering the five product types, Perlite Aggregate (EPA), Coated Perlite (EPC), Bitumen Coated Perlite (EPB), Hydrophobic Perlite (EPH) and Premixed Perlite (EPM).Part 1 of this European Standard describes the product characteristics and includes procedures for testing, evalua-tion of conformity, marking and labelling.This standard does not specify the required level of a given property to be achieved by a product to demonstrate fitness for purpose in a particular application. The levels required for a given application are to be found in regulations or non-conflicting standards.This European Standard does not cover factory made insulation products of formed shapes and boards made with expanded perlite.The products covered by this standard are not intended to be used primarily for airborne sound insulation or sound absorption applications although they may improve the performance of the buildings in these respects when installed for their primary thermal insulation intended use. |
Sì
|
|

|
00088189 |
EN 14316-2:2007 |
Thermal insulation products for buildings - In-situ thermal insulation formed from expanded perlite (EP) products - Part 2: Specification for the installed products |
This European Standard specifies the requirements covering the four product types of expanded perlite products Perlite Aggregate (EPA), Coated Perlite (EPC), Hydrophobic Perlite (EPH) and Premixed Perlite (EPM), containing less than 1 % organic material as defined by Annex D of EN 14316-1:2004 for in-situ insulation of roofs, ceilings, walls and floors. |
Sì
|
|

|
00088190 |
EN 14317-2:2007 |
Thermal insulation products for buildings - In-situ thermal insulation formed from exfoliated vermiculite (EV) products - Part 2: Specification for the installed products |
This European Standard specifies the requirements for the four types of exfoliated vermiculite products Vermiculite Aggregate (EVA), Coated Vermiculite (EVC), Hydrophobic Vermiculite (EVH) and Premixed Vermiculite (EVM), containing less than 1 % organic material as defined by Annex D of EN 14317-1:2004 for in-situ insulation of roofs, ceilings, walls and floors. |
Sì
|
|

|
00088201 |
EN 15715:2009 |
Thermal insulation products - Instructions for mounting and fixing for reaction to fire testing - Factory made products |
This standard specifies instructions for mounting and fixing for reaction to fire testing of factory made thermal insulation products. |
Sì
|
|

|
00088183 |
EN 12430:1998/A1:2006 |
Thermal insulating products for building applications - Determination of behaviour under point load |
This European Standard specifies equipment and procedures for determining the behaviour of thermal insulating products under a force applied to a small area of a test specimen at a given speed. The standard can be used to determine whether the products have sufficient strength to withstand forces applied directly to them either during installation or during application, mainly caused by pedestrian traffic. |
Sì
|
|

|
00088184 |
EN 12431:1998/A1:2006 |
Thermal insulating products for building applications - Determination of thickness for floating floor insulating products |
This European Standard specifies the equipment and procedures for determining the thickness of thermal insulating products for impact sound insulation in floating floor applications. |
Sì
|
|

|
00088187 |
EN 14064-2:2010 |
Thermal insulation products for buildings - In-situ formed loose-fill mineral wool (MW) products - Part 2: Specification for the installed products |
This European standard specifies the requirements for blown loose-fill mineral wool products installed in lofts, masonry cavity walls and frame constructions. This Part 2 of this European standard is a specification for the installed insulation products. Part 2 of this European standard describes the product characteristics that are linked to the essential requirements of the EU Construction Products Directive. Part 2 of the standard also specifies the checks and tests to be used for the declarations made by the installer of the product and the rules for the evaluation of conformity. |
Sì
|
|

|
00088125 |
EN 14933:2007 |
Thermal insulation and light weight fill products for civil engineering applications - Factory made products of expanded polystyrene (EPS) - Specification |
This European standard specifies the requirements for factory made products of expanded polystyrene, which are used in civil engineering applications, such as light weight fill and frost insulation. The products are manufactured in the form of boards or blocks. This standard describes product characteristics and includes procedures for testing, evaluation of conformity, marking and labelling. |
Sì
|
|

|
Codice progetto |
Codice Norma |
Titolo |
Sommario |
Pubblicazione UNI |
|

|
00088126 |
EN 14934:2007 |
Thermal insulation and light weight fill products for civil engineering applications - Factory made products of extruded polystyrene foam (XPS) - Specification |
This European standard specifies the requirements for factory made extruded polystyrene foam products which are used for the thermal insulation of civil engineering applications like roads and railroads and as land fill of embankments. This standard describes product characteristics and includes procedures for testing and marking and labelling. This standard does not specify the required level of a given property to be achieved by a product to demonstrate fitness for purpose in a particular application. |
Sì
|
|

|
00088213 |
EN 14707:2005+A1:2007 |
Thermal insulating products for building equipment and industrial installations - Determination of maximum service temperature for preformed pipe insulation |
This European Standard specifies the equipment and procedures for determining the maximum service temperature for preformed pipe insulation. It is applicable to thermal insulating products |
Sì
|
|

|
00088182 |
EN 12087:1997/A1:2006 |
Thermal insulating products for building applications - Determination of long term water absorption by immersion |
This European Standard specifies the equipment and procedures for determining the long term water absorption of test specimens. It is applicable to thermal insulating products. |
Sì
|
|

|
00088178 |
EN 1604:1996/A1:2006 |
Thermal insulating products for building applications - Determination of dimensional stability under specified temperature and humidity conditions |
This European Standard specifies the equipment and procedures to evaluate dimensions changes of the test specimens under specified conditions of temperature, relative humidity and duration of exposure. |
Sì
|
|

|
00088179 |
EN 1605:1996/A1:2006 |
Thermal insulating products for building applications - Determination of deformation under specified compressive load and temperature conditions |
This European Standard specifies the equipment and procedures for determining the deformation occuring under specified conditions of compressive load, temperature and time. It is applicable to thermal insulating products. |
Sì
|
|

|
00088180 |
EN 1606:1996/A1:2006 |
Thermal insulating products for building applications - Determination of compressive creep |
This European standard specifies the equipment and procedures for determining the compressive creep of test specimens under various conditions of stress |
Sì
|
|

|
00088181 |
EN 1609:1996/A1:2006 |
Thermal insulating products for building applications - Determination of dimensional short term water absorption by partial immersion |
Text is not available |
Sì
|
|

|
00088177 |
EN 1603:1996/A1:2006 |
Thermal insulating products for building applications - Determination of dimensional stability under constant normal laboratory conditions (23°C/50 % relative humidity) |
Thermal insulating products for building applications - Determination of dimensional stability under constant normal laboratory conditions (23 ¡C/50% relative humidity) |
Sì
|
|

|
00088C19 |
EN 14063-1:2004/AC:2006 |
Thermal insulation products for buildings - In-situ formed expanded clay lightweight aggregate products - Part 1: Specification for the loose-fill products before installation |
This document covers insulation materials made from expanded clay lightweight aggregate to be formed in-situ. Examples of applications for these products are insulation for roofs, walls, ceilings etc. The main addressed characteristics will be: Thermal- and water vapour transmission, mechanical properties and behaviour under water exposure for the material being installed in accordance with the following parts of the standard. |
Sì
|
|

|
00088229 |
CEN/TR 15985:2010 |
Thermal insulating products - Factory made products of expanded polystyrene (EPS) - Voluntary certification of the raw material |
- |
Sì 09/09/2010
|
|

|
00088230 |
EN 15599-1:2010 |
Thermal insulation products for building equipment and industrial installations - In-situ thermal insulation formed from expanded perlite (EP) products - Part 1: Specification for bonded and loose-fill products before installation |
This European Standard specifies the requirements for expanded perlite products which are used for the thermal insulation of building equipment and industrial installations with an operating temperature in the range of approximately -270 ºC to +650 ºC. This European Standard specifies the requirements for the four types of expanded perlite products Perlite Aggregate (EPA), Coated Perlite (EPC), Hydrophobic Perlite (EPH) and Premixed Perlite (EPM), containing less than 1 % by mass organic material.
This European Standard is a specification for the insulation products before installation. This European Standard describes the product characteristics and includes procedures for testing, evaluation of conformity, marking and labelling.
This European Standard does not cover factory made insulation products of formed shapes and boards made with expanded perlite, and does not cover products intended to be used for the insulation of buildings. |
Sì 16/09/2010
|
|

|
00088231 |
EN 15599-2:2010 |
Thermal insulation products for building equipment and industrial installations - In-situ thermal insulation formed from expanded perlite (EP) products - Part 2: Specification for the installed products |
This European Standard specifies the requirement for expanded perlite products which are used for in-situ thermal insulation of building equipment and industrial installations with an operating temperature in the range of approximately -270°C to +650°C.
This European Standard is a specification for the installed products. This European Standard also specifies the checks and test procedures to be used for the declaration made by the installer of the product. This European Standard does not include factory made insulation products of formed shapes and boards made with expanded perlite. |
Sì 16/09/2010
|
|

|
00088232 |
EN 15600-1:2010 |
Thermal insulation products for building equipment and industrial installations - In-situ thermal insulation formed from exfoliated vermiculate (EV) products - Part 1: Specification for bonded and loose-fill products before installation |
This European Standard specifies the requirements for exfoliated vermiculite products which are used for the thermal insulation of building equipment and industrial installations with an operating temperature in the range of approximately -40 ºC to +1050 ºC.
This European Standard specifies the requirements for the four types of exfoliated vermiculite products Vermiculite Aggregate (EVA), Coated Vermiculite (EVC) Hydrophobic Vermiculite (EVH) and Premixed Vermiculite (EVM), containing less than 1 % by mass organic material.
This European Standard is a specification for the insulation products before installation.
This European Standard describes the product characteristics and includes procedures for testing, evaluation of conformity, marking and labelling.
This European Standard does not cover factory made insulation products of formed shapes and boards made with exfoliated vermiculite, and does not cover products intended to be used for the insulation of buildings. |
Sì 16/09/2010
|
|

|
00088233 |
EN 15600-2:2010 |
Thermal insulation products for building equipment and industrial installations - In-situ thermal insulation formed from exfoliated vermiculate (EV) products - Part 2: Specification for the installed products |
This European Standard specifies the requirement for exfoliated vermiculite products, which are used for in situ thermal insulation of building equipment and industrial installations with an operating temperature in the range of approximately -40 ºC to +1050 ºC.
This European Standard is a specification for the installed products.
This European Standard also specifies the checks and test procedures to be used for the declaration made by the installer of the product.
This European Standard does not include factory made insulation products of formed shapes and boards made with exfoliated vermiculite. |
Sì 16/09/2010
|
|

|
00088234 |
UNI EN 16025-1:2013 |
Thermal and/or sound insulating products in building construction - Bound EPS ballastings - Part 1: Requirements for factory premixed EPS dry plaster |
- |
Sì 10/06/2013
|
|

|
00088235 |
UNI EN 16025-2:2013 |
Thermal and/ or sound insulating products in building construction - Bound EPS ballastings - Part 2: Processing of the factory premixed EPS dry plaster |
- |
Sì 10/06/2013
|
|

|
00088237 |
UNI EN 13172:2012 |
Thermal insulation products - Evaluation of conformity |
This European Standard specifies the procedures and the criteria for the evaluation of the conformity of a thermal insulating product with the relevant European product specification. |
Sì 23/02/2012
|
|

|
00088263 |
EN 13496:2013 (UNI EN 13496:2014) |
Thermal insulation products for building applications - Determination of the mechanical properties of glass fibre meshes as reinforcement for External Thermal Insulation Composite Systems with renders (ETICS) |
This European Standard specifies equipment and procedures for determining the tensile strength and elongation of glass fibre meshes which are used for the reinforcement of the base coat in External Thermal Insulation Composite Systems (ETICS). |
Sì 30/01/2014
|
|

|
00088267 |
UNI EN 13469:2012 |
Thermal insulating products for building equipment and industrial installations - Determination of water vapour transmission properties of preformed pipe insulation |
This European Standard specifies the equipment and procedure for determining the water vapour transmission properties in the steady state under specified test conditions for test specimens of preformed pipe insulation. It is applicable to thermal insulating products. It is intended to be used for homogeneous materials (see NOTE) and for products which may have integral skins or adhered facings of some different material. |
Sì 01/11/2012
|
|

|
00088268 |
UNI EN 13472:2012 |
Thermal insulating products for building equipment and industrial installations - Determination of short term water absorption by partial immersion of preformed pipe insulation |
This European Standard specifies the equipment and procedures for determining the short term water absorption of preformed pipe insulation by partial immersion in water. It is applicable to thermal insulating products. |
Sì 01/11/2012
|
|

|
Codice progetto |
Codice Norma |
Titolo |
Sommario |
Pubblicazione UNI |
|

|
00088269 |
UNI EN 14706:2012 |
Thermal insulating products for building equipment and industrial installations - Determination of maximum service temperature |
This European Standard specifies the equipment and procedures for determining the maximum service temperature of flat insulation products. It is applicable to thermal insulating products |
Sì 01/11/2012
|
|

|
00088270 |
UNI EN 14707:2012 |
Thermal insulating products for building equipment and industrial installations - Determination of maximum service temperature for preformed pipe insulation |
This European Standard specifies the equipment and procedures for determining the maximum service temperature for preformed pipe insulation. It is applicable to thermal insulating products. |
Sì 01/11/2012
|
|

|
00088272 |
UNI EN 15732:2012 |
Light weight fill and thermal insulation products for civil engineering applications (CEA) - Expanded clay lightweight aggregate products (LWA) |
This standard describes the product characteristics and includes procedures for testing, marking and labelling. This European Standard specifies the requirements for loose-fill expanded clay lightweight aggregate (expanded clay LWA) products for Civil Engineering Applications excluding the use as thermal insulation in and under buildings which are covered by European Standard EN 14063-1. The standard covers the use of expanded clay LWA as lightweight fill and insulation materials in embankments for roads, railways and other trafficked areas and as lightweight back fill for structures. This standard does not specify the required level of a given property to be achieved by a product to demonstrate fitness for purpose in a particular application. The levels required for a given application are to be found in regulations or non-conflicting standards. |
Sì 01/11/2012
|
|

|
00088276 |
UNI EN 1608:2013 |
Thermal insulating products for building applications - Determination of tensile strength parallel to faces |
- |
Sì 30/04/2013
|
|

|
00088277 |
UNI EN 1607:2013 |
Thermal insulating products for building applications - Determination of tensile strength perpendicular to faces |
- |
Sì 30/04/2013
|
|

|
00088278 |
UNI EN 822:2013 |
Thermal insulating products for building applications - Determination of length and width |
- |
Sì 30/04/2013
|
|

|
00088279 |
UNI EN 823:2013 |
Thermal insulating products for building applications - Determination of thickness |
- |
Sì 30/04/2013
|
|

|
00088280 |
UNI EN 824:2013 |
Thermal insulating products for building applications - Determination of squareness |
- |
Sì 30/04/2013
|
|

|
00088281 |
UNI EN 825:2013 |
Thermal insulating products for building applications - Determination of flatness |
- |
Sì 30/04/2013
|
|

|
00088282 |
UNI EN 826:2013 |
Thermal insulating products for building applications - Determination of compression behaviour |
- |
Sì 30/04/2013
|
|

|
00088283 |
UNI EN 1602:2013 |
Thermal insulating products for building applications - Determination of the apparent density |
- |
Sì 30/04/2013
|
|

|
00088284 |
UNI EN 1603:2013 |
Thermal insulating products for building applications - Determination of dimensional stability under constant normal laboratory conditions (23 °C/ 50 % relative humidity) |
- |
Sì 30/04/2013
|
|

|
00088285 |
UNI EN 1604:2013 |
Thermal insulating products for building applications - Determination of dimensional stability under specified temperature and humidity conditions |
- |
Sì 30/04/2013
|
|

|
00088286 |
UNI EN 1606:2013 |
Thermal insulating products for building applications - Determination of compressive creep |
- |
Sì 30/04/2013
|
|

|
00088287 |
UNI EN 1605:2013 |
Thermal insulating products for building applications - Determination of deformation under specified compressive load and temperature conditions |
- |
Sì 30/04/2013
|
|

|
00088288 |
UNI EN 12086:2013 |
Thermal insulating products for building applications - Determination of water vapour transmission properties |
- |
Sì 30/04/2013
|
|

|
00088289 |
UNI EN 12087:2013 |
Thermal insulating products for building applications - Determination of long term water absorption by immersion |
- |
Sì 30/04/2013
|
|

|
00088290 |
UNI EN 12088:2013 |
Thermal insulating products for building applications - Determination of long term water absorption by diffusion |
- |
Sì 30/04/2013
|
|

|
00088291 |
UNI EN 1609:2013 |
Thermal insulating products for building applications - Determination of short term water absorption by partial immersion |
- |
Sì 30/04/2013
|
|

|
00088292 |
UNI EN 12085:2013 |
Thermal insulating products for building applications - Determination of linear dimensions of test specimens |
- |
Sì 30/04/2013
|
|

|
Codice progetto |
Codice Norma |
Titolo |
Sommario |
Pubblicazione UNI |
|

|
00088293 |
UNI EN 12090:2013 |
Thermal insulating products for building applications - Determination of shear behaviour |
- |
Sì 30/04/2013
|
|

|
00088294 |
UNI EN 12091:2013 |
Thermal insulating products for building applications - Determination of freeze-thaw resistance |
- |
Sì 30/04/2013
|
|

|
00088295 |
UNI EN 12430:2013 |
Thermal insulating products for building applications - Determination of behaviour under point load |
- |
Sì 30/04/2013
|
|

|
00088296 |
UNI EN 12431:2013 |
Thermal insulating products for building applications - Determination of thickness for floating floor insulating products |
- |
Sì 30/04/2013
|
|

|
00088297 |
UNI EN 14063-2:2013 |
Thermal insulation products for buildings - In-situ formed expanded clay lightweight aggregate products - Part 2: Specification for the installed products |
- |
Sì 06/08/2013
|
|

|
00088298 |
UNI EN 12089:2013 |
Thermal insulating products for building applications - Determination of bending behaviour |
- |
Sì 30/04/2013
|
|

|
00088301 |
UNI EN 15101-2:2013 |
Thermal insulation products for buildings - In-situ formed loose fill cellulose (LFCI) products - Part 2: Specification for the installed products |
- |
Sì 01/11/2013
|
|

|
00088313 |
UNI EN 14315-1:2013 |
Thermal insulating products for buildings - In-situ formed sprayed rigid polyurethane (PUR) and polyisocyanurate (PIR) foam products - Part 1: Specification for the rigid foam spray system before installation |
- |
Sì 20/03/2013
|
|

|
00088314 |
UNI EN 14318-1:2013 |
Thermal insulating products for buildings - In-situ formed dispensed rigid polyurethane (PUR) and polyisocyanurate (PIR) foam products - Part 1: Specification for the rigid foam dispensed system before installation |
- |
Sì 28/02/2013
|
|

|
00088315 |
UNI EN 14315-2:2013 |
Thermal insulating products for buildings - In-situ formed sprayed rigid polyurethane (PUR) and polyisocyanurate (PIR) foam products - Part 2: Specification for the installed insulation products |
- |
Sì 28/02/2013
|
|

|
00088316 |
UNI EN 14318-2:2013 |
Thermal insulating products for buildings - In-situ formed dispensed rigid polyurethane (PUR) and polyisocyanurate (PIR) foam products - Part 2: Specification for the installed insulation products |
- |
Sì 28/02/2013
|
|

|
00088317 |
UNI EN 14319-2:2013 |
Thermal insulating products for building equipment and industrial installations - In-situ formed dispensed rigid polyurethane (PUR) and polyisocyanurate foam (PIR) products - Part 2: Specification for the installed insulation products |
- |
Sì 28/02/2013
|
|

|
00088318 |
UNI EN 14319-1:2013 |
Thermal insulating products for building equipment and industrial installations - In-situ formed dispensed rigid polyurethane (PUR) and polyisocyanurate foam (PIR) products - Part 1: Specification for the rigid foam dispensed system before installation |
- |
Sì 28/02/2013
|
|

|
00088319 |
UNI EN 14320-1:2013 |
Thermal insulating products for building equipment and industrial installations - In-situ formed sprayed rigid polyurethane (PUR) and polyisocyanurate foam (PIR) products - Part 1: Specification for the rigid foam spray system before installation |
- |
Sì 28/02/2013
|
|

|
00088320 |
UNI EN 14320-2:2013 |
Thermal insulating products for building equipment and industrial installations - In-situ formed sprayed rigid polyurethane (PUR) and polyisocyanurate foam (PIR) products - Part 2: Specification for the installed insulation products |
- |
Sì 28/02/2013
|
|

|
00088262 |
EN 16724:2015 (UNI EN 16724:2016) |
Thermal insulation products for building applications - Instructions for mounting and fixing for determination of the reaction to fire testing of external thermal Insulation composite systems (ETICS) |
- |
Sì 21/01/2016
|
|

|
00088275 |
UNI EN 16809-2:2017 |
Thermal insulation products of buildings - In-situ formed products from loose-fill expanded polystyrene (EPS) beads and bonded expanded polystyrene beads - Part 2: Specification for the bonded and loose-fill products after installation |
- |
Sì 31/03/2017
|
|

|
00088334 |
UNI EN 16783:2017 |
Thermal insulation products - Product category rules (PCR) for factory made and in-situ formed products for preparing environmental product declarations |
- |
Sì 04/05/2017
|
|

|
00088355 |
UNI EN 16383:2017 (EN 16383:2016) |
Thermal insulation products for building applications - Determination of the hygrothermal behaviour of external thermal insulation composite systems with renders (ETICS) |
- |
Sì 19/01/2017
|
|

|
00088361 |
EN 14313:2015 (UNI EN 14313:2016) |
Thermal insulation products for building equipment and industrial installations - Factory made polyethylene foam (PEF) products - Specification |
- |
Sì 21/01/2016
|
|

|
Codice progetto |
Codice Norma |
Titolo |
Sommario |
Pubblicazione UNI |
|

|
00088362 |
EN 14306:2015 (UNI EN 14306:2016) |
Thermal insulation products for building equipment and industrial installations - Factory made calcium silicate (CS) products - Specification |
- |
Sì 21/01/2016
|
|

|
00088363 |
EN 14305:2015 (UNI EN 14305:2016) |
Thermal insulation products for building equipment and industrial installations - Factory made cellular glass (CG) products - Specification |
- |
Sì 21/01/2016
|
|

|
00088364 |
EN 14307:2015 (UNI EN 14307:2016) |
Thermal insulation products for building equipment and industrial installations - Factory made extruded polystyrene foam (XPS) products - Specification |
- |
Sì 21/01/2016
|
|

|
00088365 |
EN 14308:2015 (UNI EN 14308:2016) |
Thermal insulation products for building equipment and industrial installations - Factory made rigid polyurethane foam (PUR) and polyisocyanurate foam (PIR) products - Specification |
- |
Sì 21/01/2016
|
|

|
00088366 |
EN 14309:2015 (UNI EN 14309:2016) |
Thermal insulation products for building equipment and industrial installations - Factory made products of expanded polystyrene (EPS) - Specification |
- |
Sì 21/01/2016
|
|

|
00088367 |
EN 14314:2015 (UNI EN 14314:2016) |
Thermal insulation products for building equipment and industrial installations - Factory made phenolic foam (PF) products - Specification |
- |
Sì 21/01/2015
|
|

|
00088368 |
EN 14304:2015 (UNI EN 14304:2016) |
Thermal insulation products for building equipment and industrial installations - Factory made flexible elastomeric foam (FEF) products - Specification |
- |
Sì 21/01/2016
|
|

|
00088369 |
EN 14303:2015 (UNI EN 14303:2016) |
Thermal insulation products for building equipment and industrial installations - Factory made mineral wool (MW) products - Specification |
- |
Sì 21/01/2016
|
|

|
00088370 |
EN 15501:2015 (UNI EN 15501:2016) |
Thermal insulation products for building equipment and industrial installations - Factory made expanded perlite (EP) and exfoliated vermiculite (EV) products - Specification |
- |
Sì 21/01/2016
|
|

|
00088372 |
UNI EN 14064-1:2019 (EN 14064-1:2018) |
Thermal insulation products for buildings - In-situ formed loose-fill mineral wool (MW) products - Part 1: Specification for the loose-fill products before installation |
- |
Sì 10/01/2019
|
|

|
00088383 |
EN 13164:2012+A1:2015 (UNI EN 13164:2015) |
Thermal insulation products for buildings - Factory made extruded polystyrene foam (XPS) products - Specification |
- |
Sì 02/04/2015
|
|

|
00088382 |
EN 13162:2012+A1:2015 (UNI EN 13162:2015) |
Thermal insulation products for buildings - Factory made mineral wool (MW) products - Specification |
- |
Sì 09/04/2015
|
|

|
00088381 |
EN 13170:2012+A1:2015 (UNI EN 13170:2015) |
Thermal insulation products for buildings - Factory made products of expanded cork (ICB) - Specification |
- |
Sì 09/04/2015
|
|

|
00088379 |
EN 16069:2012+A1:2015 (UNI EN 16069:2015) |
Thermal insulation products for buildings - Factory made products of polyethylene foam (PEF) - Specification |
- |
Sì 09/04/2015
|
|

|
00088378 |
EN 13168:2012+A1:2015 (UNI EN 13168:2015) |
Thermal insulation products for buildings - Factory made wood wool (WW) products - Specification |
- |
Sì 09/04/2015
|
|

|
00088377 |
EN 13167:2012+A1:2015 (UNI EN 13167:2015) |
Thermal insulation products for buildings - Factory made cellular glass (CG) products - Specification |
- |
Sì 09/04/2015
|
|

|
00088376 |
EN 13171:2012+A1:2015 (UNI EN 13171:2015) |
Thermal insulation products for buildings - Factory made wood fibre (WF) products - Specification |
- |
Sì 09/04/2015
|
|

|
00088375 |
EN 13169:2012+A1:2015 (UNI EN 13169:2015) |
Thermal insulation products for buildings - Factory made expanded perlite board (EPB) products - Specification |
- |
Sì 09/04/2015
|
|

|
00088356 |
UNI EN 16382:2017 (EN 16382:2016) |
Thermal insulation products for building applications - Determination of the pull-through resistance of plate anchors through thermal insulation products |
- |
Sì 19/01/2017
|
|

|
00088384 |
UNI EN 16977:2021 (EN 16977:2020) |
Thermal insulation products for buildings - Factory made calcium silicate (CS) products - Specification |
- |
Sì 31/01/2021
|
|

|
Codice progetto |
Codice Norma |
Titolo |
Sommario |
Pubblicazione UNI |
|

|
00088390 |
UNI EN 13467:2018 |
Thermal insulating products for building equipment and industrial installations - Determination of dimensions, squareness and linearity of preformed pipe insulation |
- |
Sì 01/02/2018
|
|

|
00088400 |
UNI EN 13165:2016 (EN 13165:2012+A2:2016) |
Thermal insulation products for buildings - Factory made rigid polyurethane foam (PU) products - Specification |
- |
Sì 22/09/2016
|
|

|
00088401 |
UNI EN 13166:2016 (EN 13166:2012+A2:2016) |
Thermal insulation products for buildings - Factory made phenolic foam (PF) products - Specification |
- |
Sì 22/09/2016
|
|

|
00088402 |
UNI EN 13163:2017 (EN 13163:2012+A2:2016) |
Thermal insulation products for buildings - Factory made expanded polystyrene (EPS) products - Specification |
- |
Sì 19/01/2017
|
|

|
00088387 |
UNI EN 17101:2018 |
Thermal insulation products for buildings - Methods of identification and test methods for one-component PU adhesive foam for External Thermal Insulation Composite Systems (ETICS) |
- |
Sì 11/10/2018
|
|

|
00088415 |
UNI EN 13495:2019 |
Thermal insulation products for building applications - Determination of the pull-off resistance of external thermal insulation composite systems (ETICS) (foam block test) |
- |
Sì 30/10/2019
|
|

|
00088417 |
UNI EN 13494:2019 |
Thermal insulation products for building applications - Determination of the tensile bond strength of the adhesive and of the base coat to the thermal insulation material |
- |
Sì 30/10/2019
|
|

|
00088333 |
UNI EN 17140:2021 (EN 17140:2020) |
Thermal insulation products for buildings - Factory-made vacuum insulation panels (VIP) - Specification |
- |
Sì 31/01/2021
|
|

|
00088419 |
UNI EN ISO 29767:2019 |
Thermal insulating products for building applications - Determination of short-term water absorption by partial immersion (ISO 29767:2019) |
- |
Sì 17/10/2019
|
|

|
00088420 |
UNI EN ISO 16535:2019 |
Thermal insulating products for building applications - Determination of long-term water absorption by immersion (ISO 16535:2019) |
- |
Sì 17/10/2019
|
|

|
00088421 |
UNI EN ISO 16536:2019 |
Thermal insulating products for building applications - Determination of long-term water absorption by diffusion (ISO 16536:2019) |
- |
Sì 17/10/2019
|
|

|
00088423 |
UNI EN ISO 9229:2021 (EN ISO 9229:2020) |
Thermal insulation - Vocabulary (ISO 9229:2020) |
- |
Sì 31/01/2021
|
|

|
00088424 |
UNI EN 16809-1:2020 (EN 16809-1:2019) |
Thermal insulation products of buildings - In-situ formed products from loose-fill expanded polystyrene (EPS) beads and bonded expanded polystyrene beads - Part 1: Specification for the bonded and loose-fill products before installation |
- |
Sì 20/02/2020
|
|

|
00088453 |
UNI EN 15101-1:2019 (EN 15101-1:2013+A1:2019) |
Thermal insulation products for buildings - In-situ formed loose fill cellulose (LFCI) products - Part 1: Specification for the products before installation |
- |
Sì 30/05/2019
|
|

|
00088454 |
UNI EN ISO 16546:2021 (EN ISO 16546:2020) |
Thermal insulating products for building applications - Determination of freeze-thaw resistance (ISO 16546:2020) |
- |
Sì 31/01/2021
|
|

|
00088455 |
UNI EN ISO 29470:2021 (EN ISO 29470:2020) |
Thermal insulating products for building applications - Determination of the apparent density (ISO 29470:2020) |
- |
Sì 31/01/2021
|
|

|
00088456 |
UNI EN ISO 16534:2021 (EN ISO 16534:2020) |
Thermal insulating products for building applications - Determination of compressive creep (ISO 16534:2020) |
- |
Sì 31/01/2021
|
|

|
00088437 |
UNI EN 16863:2023 |
Thermal insulation products for buildings - Factory made reflective insulation (RI) products - Specification |
- |
Sì 13/07/2023
|
|

|
00088460 |
UNI EN ISO 29469:2022 |
Thermal insulating products for building applications - Determination of compression behaviour (ISO 29469:2022) |
- |
Sì 15/12/2022
|
|

|
00088479 |
UNI EN 13497:2021 (EN 13497:2018+A1:2021) |
Thermal insulation products for building applications - Determination of the resistance to impact of external thermal insulation composite systems (ETICS) |
- |
Sì 18/03/2021
|
|

|
Codice progetto |
Codice Norma |
Titolo |
Sommario |
Pubblicazione UNI |
|

|
00088476 |
UNI EN ISO 18099:2022 |
Thermal insulating products for building equipment and industrial installations - Determination of the coefficient of thermal expansion (ISO 18099:2022) |
- |
Sì 13/10/2022
|
|

|
00088473 |
UNI EN ISO 12628:2022 |
Thermal insulating products for building equipment and industrial installations - Determination of dimensions, squareness and linearity of preformed pipe insulation (ISO 12628:2022) |
- |
Sì 13/10/2022
|
|

|
00088470 |
UNI EN ISO 29768:2022 |
Thermal insulating products for building applications - Determination of linear dimensions of test specimens (ISO 29768:2022) |
- |
Sì 20/10/2022
|
|

|
00088469 |
UNI EN ISO 29770:2022 |
Thermal insulating products for building applications - Determination of thickness for floating-floor insulating products (ISO 29770:2022) |
- |
Sì 13/10/2022
|
|

|
00088468 |
UNI EN ISO 29465:2022 |
Thermal insulating products for building applications - Determination of length and width (ISO 29465:2022) |
- |
Sì 13/10/2022
|
|

|
00088467 |
UNI EN ISO 29466:2022 |
Thermal insulating products for building applications - Determination of thickness (ISO 29466:2022) |
- |
Sì 15/12/2022
|
|

|
00088466 |
UNI EN ISO 29468:2022 |
Thermal insulating products for building applications - Determination of flatness (ISO 29468:2022) |
- |
Sì 13/10/2022
|
|

|
00088465 |
UNI EN ISO 29766:2023 |
Thermal insulating products for building applications - Determination of tensile strength parallel to faces (ISO 29766:2022) |
- |
Sì 19/01/2023
|
|

|
00088478 |
UNI EN ISO 12623:2022 |
Thermal insulating products for building equipment and industrial installations - Determination of short-term water absorption by partial immersion of preformed pipe insulation (ISO 12623:2022) |
- |
Sì 13/10/2022
|
|

|
00088477 |
UNI EN ISO 12629:2022 |
Thermal insulating products for building equipment and industrial installations - Determination of water vapour transmission properties of preformed pipe insulation (ISO 12629:2022) |
- |
Sì 13/10/2022
|
|

|
00088475 |
UNI EN ISO 18098:2022 |
Thermal insulating products for building equipment and industrial installations - Determination of the apparent density of preformed pipe insulation (ISO 18098:2022) |
- |
Sì 13/10/2022
|
|

|
00088474 |
UNI EN ISO 18096:2022 |
Thermal insulating products for building equipment and industrial installations - Determination of maximum service temperature for preformed pipe insulation (ISO 18096:2022) |
- |
Sì 13/10/2022
|
|

|
00088472 |
UNI EN ISO 12624:2022 |
Thermal insulating products for building equipment and industrial installations - Determination of trace quantities of water-soluble chloride, fluoride, silicate, sodium ions and pH (ISO 12624:2022) |
- |
Sì 13/10/2022
|
|

|
00088471 |
UNI EN ISO 18097 |
Thermal insulating products for building equipment and industrial installations - Determination of maximum service temperature (ISO 18097:2022) |
- |
Sì 13/10/2022
|
|
Codice progetto |
Codice Norma |
Titolo |
Sommario |
Pubblicazione UNI |
|
00088114 |
EN 14707:2005 |
Thermal insulating products for building equipment and industrial installations - Determination of maximum service temperature for preformed pipe insulation |
This European Standard specifies the equipment and procedures for determining the maximum service temperature for preformed pipe insulation. It is applicable to thermal insulating products. |
Non prevista
|
|
00088152 |
EN 13164:2001/A1:2004 |
Thermal insulation products for buildings - Factory made products of extruded polystyrene foam (XPS) - Specification |
Testo non disponibile |
Non prevista
|
|
00088153 |
EN 13166:2001/A1:2004 |
Thermal insulation products for buildings - Factory made products of phenolic foam (PF) - Specification |
Testo non disponibile |
Non prevista
|
|
00088154 |
EN 13167:2001/A1:2004 |
Thermal insulation products for buildings - Factory made cellular glass (CG) products - Specification |
Testo non disponibile |
Non prevista
|
|
00088155 |
EN 13168:2001/A1:2004 |
Thermal insulation products for buildings - Factory made wood wool (WW) products - Specification |
Testo non disponibile |
Non prevista
|
|
00088156 |
EN 13169:2001/A1:2004 |
Thermal insulation products for buildings - Factory made products of expanded perlite (EPS) - Specification |
Testo non disponibile |
Non prevista
|
|
00088157 |
EN 13171:2001/A1:2004 |
Thermal insulation products for buildings - Factory made wood fibre (WF) products - Specification |
Testo non disponibile |
Non prevista
|
|
00088064 |
EN 14313:2009 |
Thermal insulation products for building equipment and industrial installations - Factory made polyethylene foam (PEF) products - Specification |
This European Standard specifies the requirements for factory made flexible polyethylene foam products which are used for the thermal insulation of building equipment and industrial installations with an operating temperature in the range of approximately – 80 °C to + 150 °C. This standard describes product characteristics and includes procedures for testing, evaluation of conformity, marking and labelling. Products with a declared thermal conductivity greater than 0,050 W/(m•K) at 10 °C are not covered by this standard. This standard does not cover products for the insulation of the building structure. |
Non prevista
|
|
00088065 |
EN 14303:2009 |
Thermal insulation products for building equipment and industrial installations - Factory made mineral wool (MW) products - Specification |
This European Standard specifies the requirements for factory made mineral wool products, which are used for the thermal insulation of building equipment and industrial installations with an operating temperature range of approximately 0°C to + 800°C. This European Standard describes product characteristics and includes procedures for testing, evaluation of conformity, marking and labelling. Products with a declared thermal conductivity greater than 0,065 W/(m•K) at 10 °C are not covered by this standard. This Eurpean Standard does not cover products for in situ insulation or products for the insulation of the building structure. |
Non prevista
|
|
00088066 |
EN 14304:2009 |
Thermal insulation products for building equipment and industrial installations - Factory made flexible elastomeric foam (FEF) products - Specification |
This European Standard specifies the requirements for factory made flexible elastomeric foam products which are used for the thermal insulation of building equipment and industrial installations with an operating temperature in the range of approximately – 200 °C to + 175 °C. Products with a declared thermal conductivity greater than 0,050 W/(m•K) at 10 °C are not covered by this standard. This European Standard does not cover products for the insulation of the building structure. |
Non prevista
|
|
00088067 |
EN 14305:2009 |
Thermal insulation products for building equipment and industrial installations - Factory made cellular glass (CG) products - Specification |
This European Standard specifies the requirements for factory made cellular glass products which are used for the thermal insulation of building equipment and industrial installations with an operating temperature range of approximately – 265 °C to + 430 °C. This standard describes product characteristics and includes procedures for testing, evaluation of conformity, marking and labelling. Products with a declared thermal conductivity greater than 0,065 W/(m•K) at 10 °C are not covered by this standard. This standard does not cover products for the insulation of the building structure. |
Non prevista
|
|
00088068 |
EN 14306:2009 |
Thermal insulation products for building equipment and industrial installations - Factory made calcium silicate (CS) products - Specification |
This European Standard specifies the requirements for factory made calcium silicate products which are used for the thermal insulation of building equipment and industrial installations with an operating temperature range of approximately – 170°C to + 1 100 °C.
This standard describes product characteristics and includes procedures for testing, evaluation of conformity, marking and labelling. Products with a declared thermal conductivity greater than 0,6 W/(mK) at 10 °C are not covered by this standard. This standard does not cover products intended to be used for the insulation of the building structure. |
Non prevista
|
|
00088069 |
EN 14314:2009 |
Thermal insulation products for building equipment and industrial installations - Factory made phenolic foam (PF) products - Specification |
1 Scope This European Standard specifies the requirements for factory made phenolic foam products which are used for the thermal insulation of building equipment and industrial installations with an operating temperature in the range of approximately – 200 °C to + 120 °C. This standard describes product characteristics and includes procedures for testing, evaluation of conformity, marking and labelling. Products with a declared thermal conductivity greater than 0,050 W/(m•K) at 10 °C are not covered by this standard. This standard does not cover products for in situ insulation (blowing or pouring) or products for the insulation of the building structure. |
Non prevista
|
|
00088071 |
EN 14308:2009 |
Thermal insulation products for building equipment and industrial installations - Factory made rigid polyurethane foam (PUR) and polyisocyanurate foam (PIR) products - Specification |
This European Standard specifies the requirements for factory made rigid polyurethane foam (PUR) and polyisocyanurate foam (PIR) products, which are used for the thermal insulation of building equipment and industrial installations, with an operating temperature range of approximately, – 200 °C to + 200 °C. This standard describes product characteristics and includes procedures for testing, evaluation of conformity, marking and labelling. Products with a declared thermal conductivity greater than 0,100 W/(m • K) at 10 °C are not covered by this standard. This standard does not cover products for in situ-insulation or products for the insulation of the building structure. |
Non prevista
|
|
00088117 |
EN 14309:2009 |
Thermal insulation products for building equipment and industrial installations - Factory made products of expanded polystyrene (EPS) - Specification |
This European Standard specifies the requirements for factory made products of expanded polystyrene which are used for the thermal insulation of building equipment and industrial installations with an operating temperature range of approximately – 180 °C to + 80 °C. This standard describes product characteristics and includes procedures for testing, evaluation of conformity, marking and labelling. Products with a declared thermal conductivity greater than 0,060 W/(m•K) at 10 °C are not covered by this standard. This standard does not cover products for in situ insulation or products for the insulation of the building structure. |
Non prevista
|
|
00088079 |
EN 13467:2001 |
Thermal insulating products for building equipment and industrial installations - Determination of dimensions, squareness and linearity of preformed pipe insulation |
This European Standard specifies the equipment and procedures for determining the dimensions, squareness and linearity of preformed pipe insulation, supplied in one piece, half sections or segments. It is applicable to thermal insulating products. |
Non prevista
|
|
00088070 |
EN 14307:2009 |
Thermal insulation products for building equipment and industrial installations - Factory made extruded polystyrene foam (XPS) products - Specification |
This European Standard specifies the requirements for factory made extruded polystyrene foam products which are used for the thermal insulation of building equipment and industrial installations with an operating temperature in the range of approximately - 180 °C to + 75 °C. This standard describes product characteristics and includes procedures for testing, evaluation of conformity, marking and labelling. Products with a declared thermal conductivity greater than 0,060 W/(m.K) at a mean temperature of 10 °C are not covered by this standard. This standard does not cover products intended to be used for the insulation of the building structure nor for acoustical insulation. |
Non prevista
|
|
00088159 |
EN 13165:2001/prA2:2004 |
Thermal insulation products for buildings - Factory made rigid polyurethane foam (PUR) products - Specification |
This European Standard specifies the requirements for factory made products of polyurethane rigid foam, with or without facings or coatings and with or without integral reinforcement, which are used for the thermal insulation of buildings. The products are manufactured in the form of boards. The standard also covers multilayered products and composite insulation products, laminates and cladding panels in which polyurethane rigid foam is the main insulant. The standard describes product characteristics and includes procedures for testing, marking and labelling. |
Non prevista
|
|
00088151 |
EN 13165:2001/A1:2004 |
Thermal insulation products for buildings - Factory made rigid polyurethane foam (PUR) products - Specification |
Text is not available |
Non prevista
|
|
00088C09 |
EN 13162:2001/AC:2005 |
Thermal insulation products for buildings - Factory made mineral wool (MW) products - Specification |
This European Standard specifies the requirements for factory made products of mineral wool, with or without facings, which are used for the thermal insulation of buildings. The products are manufactured in the form of rolls, batts, slabs or boards. This standard describes product characteristics and includes procedures for testing, marking and labelling. Products covered by this standard are also used in prefabricated thermal insulation systems and composite panels; the structural performance of systems incorporating these products is not covered. |
Non prevista
|
|
Codice progetto |
Codice Norma |
Titolo |
Sommario |
Pubblicazione UNI |
|
00088C10 |
EN 13163:2001/AC:2005 |
Thermal insulation products for buildings - Factory made products of expanded polystyrene (EPS) - Specification |
This European Standard specifies the requirements for factory made products of expanded polystyrene, with or without facings or coatings which are used for the thermal insulation of buildings. The products are manufactured in the form of boards or rolls or other preformed ware. The standard describes product characteristics and includes procedures for testing, marking and labelling. Products covered by this standard are also used in prefabricated thermal insulation systems and composite panels; the structural performance of systems incorporating these products is not covered. |
Non prevista
|
|
00088C17 |
EN 13170:2001/AC:2005 |
Thermal insulation products for buildings - Factory made products of expanded cork (ICB) - Specification |
This European Standard specifies the requirements for factory made products from expanded cork, agglomerated without additional binders, which are used for the thermal insulation of buildings. The products are delivered in the form of boards, with or without facings. The standard describes product characteristics and gives the test methods and procedures for marking, labelling and packaging. Products covered by this European Standard are also used in thermal insulation systems and composite panels; the structural performance of systems incorporating these products is not covered. |
Non prevista
|
|
00088127 |
EN 13172:2001/A1:2005 |
Thermal insulating products - Evaluation of conformity |
This amendment to EN 13172:2001 makes some corrections and clarifications and a re-arrangement to the text:
 Terms and definitions have been modified and information on grouping have been added in Clause 4;
 Clause 7 is renamed as Annex F (informative) and the content has been revised;
 Annex A (informative, for voluntary certification) has been updated to avoid unnecessary testing in the case of nonconformity and Table A.1 has been updated to cover both the standards for factory made building products and for products for building equipment |
Non prevista
|
|
00088203 |
EN 13162:2008 |
Thermal insulation products for buildings - Factory made mineral wool (MW) products - Specification |
This European Standard specifies the requirements for factory made mineral wool products, with or without facings, which are used for the thermal insulation of buildings. This European Standard describes product characteristics and includes procedures for testing, evaluation of conformity, marking and labelling. Products with a declared thermal resistance lower than 0,25 m2⋅K/W or a declared thermal conductivity greater than 0,060 W/(m⋅K) at 10 °C are not covered by this European Standard. |
Non prevista
|
|
00088204 |
EN 13163:2008 |
Thermal insulation products for buildings - Factory made products of expanded polystyrene (EPS) - Specification |
This European Standard specifies the requirements for factory made products of expanded polystyrene, with or without facings or coatings, which are used for the thermal insulation of buildings. This European Standard describes product characteristics and includes procedures for testing, evaluation of conformity, marking and labelling. Products with a declared thermal resistance lower than 0,25 m2⋅K/W or a declared thermal conductivity greater than 0,060 W/(m⋅K) at 10 °C are not covered by this European Standard. |
Non prevista
|
|
00088205 |
EN 13164:2008 |
Thermal insulation products for buildings - Factory made products of extruded polystyrene foam (XPS) - Specification |
This European Standard specifies the requirements for factory made products of extruded polystyrene foam, with or without facings or coatings, which are used for thermal insulation of buildings. This European Standard describes product characteristics and includes procedures for testing, evaluation of conformity, marking and labelling. Products with a declared thermal resistance lower than 0,25 m2⋅K/W or a declared thermal conductivity greater than 0,060 W/(m⋅K) at 10 °C are not covered by this European Standard. |
Non prevista
|
|
00088206 |
EN 13165:2008 |
Thermal insulation products for buildings - Factory made rigid polyurethane foam (PUR) products - Specification |
This European Standard specifies the requirements for factory made rigid polyurethane foam (PUR) products, with or without rigid or flexible facings or coatings and with or without integral reinforcement, which are used for the thermal insulation of buildings. PUR also includes polyisocyanurate foam (PIR). This European Standard describes product characteristics and includes procedures for testing, evaluation of conformity, marking and labelling. Products with a declared thermal resistance lower than 0,05 m2⋅K/W or a declared thermal conductivity greater than 0,1 W/(m⋅K) at 10 °C are not covered by this European Standard. |
Non prevista
|
|
00088207 |
EN 13166:2008 |
Thermal insulation products for buildings - Factory made products of phenolic foam (PF) - Specification |
This European Standard specifies the requirements for factory made products of phenolic foam, with or without facings, which are used for the thermal insulation of buildings. This European Standard describes product characteristics and includes procedures for testing, evaluation of conformity, marking and labelling. Products with a declared thermal resistance lower than 0,40 m2⋅K/W or a declared thermal conductivity greater than 0,050 W/(m⋅K) at 10 °C are not covered by this European Standard. |
Non prevista
|
|
00088208 |
EN 13167:2008 |
Thermal insulation products for buildings - Factory made cellular glass (CG) products - Specification |
This European Standard specifies the requirements for factory made cellular glass products, with or without facings, which are used for the thermal insulation of buildings. This European Standard describes product characteristics and includes procedures for testing, evaluation of conformity, marking and labelling. Products with a declared thermal resistance lower than 0,50 m2⋅K/W or a declared thermal conductivity greater than 0,065 W/(m⋅K) at 10 °C are not covered by this European Standard. |
Non prevista
|
|
00088186 |
EN 14064-1:2010 |
Thermal insulation products for buildings - In-situ formed loose-fill mineral wool (MW) products - Part 1: Specification for the loose-fill products before installation |
This document specifies the requirements for blown loose-fill mineral wool products for in-situ installation in lofts, masonry cavity walls and frame constructions. Part 1 of this European standard is a specification for the insulation products before installation. It describes the product characteristics and includes procedures for testing, marking and labelling. |
Non prevista
|
|
00088020 |
EN ISO 9229:2007 |
Thermal insulation - Vocabulary (ISO 9229:1997) |
This draft European Standard gives definitons which are used in the field of thermal insulation covering materials, products, components, applications and terms. Some of the terms used in this standard may have a different meaning when used in other industries of applications. |
Non prevista
|
|
00088202 |
EN 13172:2008 |
Thermal insulating products - Evaluation of conformity |
This European Standard specifies the procedures and the criteria for the evaluation of the conformity of a thermal insulating product with the relevant European product specification |
Non prevista
|
|
00088209 |
EN 13168:2008 |
Thermal insulation products for buildings - Factory made wood wool (WW) products - Specification |
This European Standard specifies the requirements for factory made products of wood wool, with or without facings, which are used for the thermal insulation of buildings. This European Standard also specifies the requirements for the factory made composite products, made from wood wool in combination with other insulation materials. This European Standard describes product characteristics and includes procedure for testing, evaluation of conformity, marking and labelling. Products with a declared thermal resistance lower than 0,15 m2K/W at 10 °C or a declared thermal conductivity greater than 0,1 W/(mK) at 10°C are not covered by this European Standard. |
Non prevista
|
|
00088210 |
EN 13169:2008 |
Thermal insulation products for buildings - Factory made products of expanded perlite (EPB) - Specification |
This European Standard specifies the requirements for factory made products of expanded perlite, with or without facings or coatings, which are used for the thermal insulation of buildings. This European Standard also covers composite insulation boards (see Annex D). This European Standard describes product characteristics and includes procedures for testing, evaluation of conformity, marking and labelling. Products with a declared thermal resistance lower than 0,20 m2K/W at 10 °C or a declared thermal conductivity greater than 0,070 W/(mK), at 10 °C, are not covered by this European Standard. |
Non prevista
|
|
00088211 |
EN 13170:2008 |
Thermal insulation products for buildings - Factory made products of expanded cork (ICB) - Specification |
This European Standard specifies the requirements for factory made products of expanded cork, which are used for the thermal insulation of buildings. The products are made with granulated cork agglomerated without additional binders and are delivered as boards without facings. This European Standard describes product characteristics and includes procedures for testing, evaluation of conformity, marking, labelling and packaging. Products with a declared thermal resistance lower than 0,25 m2 K/W, at 10 °C, or a declared thermal conductivity greater than 0,060 W//mK), at 10°C, are not covered by this European Standard. |
Non prevista
|
|
00088212 |
EN 13171:2008 |
Thermal insulating products for buildings - Factory made wood fibre (WF) products - Specification |
This European Standard specifies the requirements for factory made wood fibre products, with or without facings or coatings, which are used for the thermal insulation of buildings . This European Standard describes product characteristics and includes procedures for testing, evaluation of conformity, marking and labelling. Products with a declared thermal resistanze lower than 0,50 m2K/W at 10 °C or a declared thermal conductivity greater than 0,070 W/(mK), at 10 °C, are not covered by this European Standard. |
Non prevista
|
|
00088219 |
EN 13162:2012 (UNI EN 13162:2013) |
Thermal insulation products for buildings - Factory made mineral wool (MW) products - Specification |
- |
Non prevista
|
|
00088220 |
EN 13163:2012 (UNI EN 13163:2013) |
Thermal insulation products for buildings - Factory made expanded polystyrene (EPS) products - Specification |
- |
Non prevista
|
|
00088221 |
EN 13164:2012 (UNI EN 13164:2013) |
Thermal insulation products for buildings - Factory made extruded polystyrene foam (XPS) products - Specification |
- |
Non prevista
|
|
00088222 |
EN 13165:2012 (UNI EN 13165:2013) |
Thermal insulation products for buildings - Factory made rigid polyurethane foam (PU) products - Specification |
- |
Non prevista
|
|
Codice progetto |
Codice Norma |
Titolo |
Sommario |
Pubblicazione UNI |
|
00088223 |
EN 13166:2012 (UNI EN 13166:2013) |
Thermal insulation products for buildings - Factory made phenolic foam (PF) products - Specification |
- |
Non prevista
|
|
00088224 |
EN 13167:2012 (UNI EN 13167:2013) |
Thermal insulation products for buildings - Factory made cellular glass (CG) products - Specification |
- |
Non prevista
|
|
00088225 |
EN 13168:2012 (UNI EN 13168:2013) |
Thermal insulation products for buildings - Factory made wood wool (WW) products - Specification |
- |
Non prevista
|
|
00088226 |
EN 13169:2012 (UNI EN 13169:2013) |
Thermal insulation products for buildings - Factory made expanded perlite board (EPB) products - Specification |
- |
Non prevista
|
|
00088227 |
EN 13170:2012 (UNI EN 13170:2013) |
Thermal insulation products for buildings - Factory made products of expanded cork (ICB) - Specification |
- |
Non prevista
|
|
00088228 |
EN 13171:2012 (UNI EN 13171:2013) |
Thermal insulation products for buildings - Factory made wood fibre (WF) products - Specification |
- |
Non prevista
|
|
00088236 |
EN 16069:2012 (UNI EN 16069:2013) |
Thermal insulation products for buildings - Factory made products of polyethylene foam (PEF) - Specification |
This European Standard specifies the requirements for factory made products of polyethylene foam (PEF), with or without facings or coatings, which are used for thermal insulation of buildings. The products are manufactured in the form of boards or rolls or other performed ware. This standard describes product characteristics and includes procedures for testing, evaluation of conformity, marking and labelling. Products covered by this standard are also used in prefabricated thermal insulating systems and composite panels; the performance of systems incorporating these products is not covered. This European Standard does not specify the required level of a given property to be achieved by a products to demonstrate fitness for purpose in a particular application. The levels required for a given application are to be found in regulations or non-conflicting standards. Products with a declared thermal resistance lower than 0,05 m2K/W or a declared thermal conductivity greater than 0,05 W/(m.K) at 10 °C are not covered by this European Standard. This standard does not cover in situ insulation products and products intended to be used for the insulation of building equipment and industrial installations. Further excluded are non-foamed materials such as bubble films, foils etc. |
Non prevista
|
|
00088271 |
UNI EN 15501:2013 |
Thermal insulation products for building equipment and industrial installations - Factory made expanded perlite (EP) and exfoliated vermiculite (EV) products - Specification |
- |
Non prevista
|
|
00088300 |
UNI EN 15101-1:2013 |
Thermal insulation products for buildings - In-situ formed loose fill cellulose (LFCI) products - Part 1: Specification for the products before installation |
- |
Non prevista
|
|
00088329 |
UNI EN 14308:2009+A1:2013 |
Thermal insulation products for building equipment and industrial installations - Factory made rigid polyurethane foam (PUR) and polyisocyanurate foam (PIR) products - Specification |
- |
Non prevista
|
|
00088328 |
UNI EN 14305:2009+A1:2013 |
Thermal insulation products for building equipment and industrial installations - Factory made cellular glass (CG) products - Specification |
- |
Non prevista
|
|
00088321 |
UNI EN 14303:2009+A1:2013 |
Thermal insulation products for building equipment and industrial installations - Factory made mineral wool (MW) products - Specification |
- |
Non prevista
|
|
00088322 |
UNI EN 14304:2009+A1:2013 |
Thermal insulation products for building equipment and industrial installations - Factory made flexible elastomeric foam (FEF) products - Specification |
- |
Non prevista
|
|
00088323 |
UNI EN 14306:2009+A1:2013 |
Thermal insulation products for building equipment and industrial installations - Factory made calcium silicate (CS) products - Specification |
- |
Non prevista
|
|
00088327 |
UNI EN 14307:2009+A1:2013 |
Thermal insulation products for building equipment and industrial installations - Factory made extruded polystyrene foam (XPS) products - Specification |
- |
Non prevista
|
|
00088324 |
UNI EN 14309:2009+A1:2013 |
Thermal insulation products for building equipment and industrial installations - Factory made products of expanded polystyrene (EPS) - Specification |
- |
Non prevista
|
|
00088325 |
UNI EN 14313:2009+A1:2013 |
Thermal insulation products for building equipment and industrial installations - Factory made polyethylene foam (PEF) products - Specification |
- |
Non prevista
|
|
00088326 |
UNI EN 14314:2009+A1:2013 |
Thermal insulation products for building equipment and industrial installations - Factory made phenolic foam (PF) products - Specification |
- |
Non prevista
|
|
00088380 |
EN 13163:2012+A1:2015 (UNI EN 13163:2015) |
Thermal insulation products for buildings - Factory made expanded polystyrene (EPS) products - Specification |
- |
Non prevista
|
|
00088374 |
EN 13166:2012+A1:2015 (UNI EN 13166:2015) |
Thermal insulation products for buildings - Factory made phenolic foam (PF) products - Specification |
- |
Non prevista
|
|