User

Password

Recupero Password

CT 232 - Sistemi di compressione ed espansione e sistemi di accumulo di energia meccanica

Coordinatore CT: N.D. - Project Leader: Molinari Dario - Project Assistant: N.D. - Maggiori Informazioni

In questa sezione è riportata tutta la documentazione del Gruppo Consultivo o della Commissione Tecnica, suddivisa tra attività nazionale svolta direttamente e attività CEN e/o ISO svolta dalla CT in qualittà di Mirror Committee.

ISO/TC 118 - Compressors and pneumatic tools, machines and equipment

Norme vigenti

Chiudi Tutti

Codice progetto

Codice Norma

Titolo

Sommario

Pubblicazione UNI

Espandi

ISO 2787

ISO 2787:1984

Rotary and percussive pneumatic tools - Performance tests

This second edition cancels and replaces the first edition (1974). Specifies a test method and technical conditions for the supply of pneumatic tools and gives detailed instructions on the measurements of power output and air consumption and means of adjusting the measured values to specified conditions. A format for test report is included for rotary tools in annex A and in annex B for percussive tools. Annex C gives a procedure of impact energy.

Non prevista

Espandi

ISO 8573-3

ISO 8573-3:1999

Compressed air -- Part 3: Test methods for measurement of humidity

-

Non prevista

Espandi

ISO 8573-4

ISO 8573-4:2001

Compressed air - Part 4: Test methods for solid particle content

-

Non prevista

Espandi

ISO 8573-5

ISO 8573-5:2001

Compressed air - Part 5: Test methods for oil vapour and organic solvent content

-

Non prevista

Espandi

ISO 8573-6

ISO 8573-6:2003

Compressed air - Part 6: Test methods for gaseous contaminant content

ISO 8573-6:2003 provides a selection of suitable test methods for the measurement of contamination gases in compressed air. It specifies sampling technique, measurement and evaluation, uncertainty considerations and reporting for the applicable gaseous contaminants carbon monoxide, carbon dioxide, sulphur dioxide, nitric oxide, nitrogen dioxide, and hydrocarbons in the range C1 to C5 (see ISO 8573-5 for C6 and above). The methods given are also suitable for other gases.

Non prevista

Espandi

ISO 8573-7

ISO 8573-7:2003

Compressed air - Part 7: Test method for viable microbiological contaminant content

ISO 8573-7:2003 specifies a test method for distinguishing viable, colony-forming, microbiological organisms (e.g. yeast, bacteria, endotoxins) from other solid particles which may be present in compressed air. One of a series of standards aimed at harmonizing air contamination measurements, it provides a means of sampling, incubating and determining the number of microbiological particles. The test method is suitable for determining purity classes in accordance with ISO 8573-1, and is intended to be used in conjunction with ISO 8573-4 when there is need to identify solid particles that are also viable, colony-forming units.

Non prevista

Espandi

ISO 8662-1

ISO 8662-1:1988

Hand-held portable power tools - Measurement of vibrations at the handle -- Part 1: General

Specifies the type test methods for the laboratory measurement of vibrations in the handles of tools. nThis part describes thebasic requirements for evaluating vibrations; it is not intended for assessment of human to vibrations.

Non prevista

Espandi

ISO 8662-11

ISO 8662-11:1999

Hand-held portable power tools - Measurement of vibrations at the handle - Part 11: Fastener driving tools

-

Non prevista

Espandi

ISO 8662-13

ISO 8662-13:1997

Hand-held portable power tools - Measurement of vibrations at the handle - Part 13: Die grinders

-

Non prevista

Espandi

ISO 8662-14

ISO 8662-14:1996

Hand-held portable power tools - Measurement of vibrations at the handle - Part 14: Stone-working tools and needle scalers

Describes a laboratory method of measuring the vibrations at the handles of hand-held stone-working power tools and needle scalers. Establishes the magnitude of vibrations at the handles when operating on the artificial load.

Non prevista

Espandi

ISO 10440-2

ISO 10440-2:2001

Petroleum and natural gas industries - Rotary-type positive-displacement compressors - Part 2: Packaged air compressors (oil-free)

-

Non prevista

Espandi

ISO 10442

ISO 10442:2002

Petroleum, chemical and gas service industries -- Packaged, integrally geared centrifugal air compressors

ISO 10442:2002 specifies requirements and gives recommendations for the design, materials, fabrication, inspection, testing and preparation for shipment of constant-speed, packaged, integrally geared centrifugal air compressors, including their accessories, for use in the petroleum, chemical and gas service industries. It is also applicable to gas services other than air that are non-hazardous and non-toxic. It is not applicable to machines that develop a pressure rise of less than 35 kPa above atmospheric pressure, which are classed as fans or blowers.

Non prevista

Espandi

ISO 13631

ISO 13631:2002

Petroleum and natural gas industries - Packaged reciprocating gas compressors

ISO 13631:2002 gives requirements and recommendations for the design, materials, fabrication, inspection, testing and preparation for shipment of packaged skid-mounted, reciprocating, separable or integral compressors with lubricated cylinders and their prime movers, for use in the petroleum and natural gas industries for the compression of hydrocarbon gas.

It is also applicable to all necessary auxiliary equipment, such as water and gas coolers, silencers, emission control equipment, filters, separators, control panel, piping, etc., required to install an operable unit in compliance with the purchase specifications and with the intent of minimizing field construction and field-purchased equipment.

ISO 13631:2002 is not applicable to the following:

reciprocating compressors for petroleum and natural gas industries covered by ISO 13707;
column-mounted compressors;
non-lubricated compressors;
compressors having trunk-type (automotive-type) pistons that also serve as crossheads;
utility or instrument air compressors with a discharge gauge pressure of 0,9 MPa (9 bar) or less;
compressors driven by diesel engine, gas turbine and steam turbine prime movers.

Non prevista

Espandi

ISO 15744

ISO 15744:2002

Hand-held non-electric power tools - Noise measurement code - Engineering method (grade 2)

This International Standard specifies test methods for the measurement, determination and declaration of the noise emission from hand-held non-electric power tools. It prescribes the loading and working conditions under which can be determined
1. the noise emission, under specified load conditions, expressed as the sound power level, and
2. the emission sound pressure level at the work station under specified load conditions.
This International Standard is applicable to typical hand-held non-electric power tools including rotary tools, orbital and random orbital sanders, rotary and non-rotary reciprocating and percussive tools and a variety of assembly tools. It is not applicable to cartridge-operated tools, fastener driving tools (e.g. nailers, staplers) or any tool powered by an internal combustion engine, nor is it applicable to breakers or other power tools which, when placed on the market, are required to meet the provisions of legislation specifying test methods and imposing limits on noise emission from, for example, equipment used outdoors.

Non prevista

Espandi

ISO 28927-12

ISO 28927-12:2012

Hand-held portable power tools — Test methods for evaluation of vibration emission — Part 12: Die grinders

-

Non prevista

Espandi

ISO 5393

ISO 5393:2017

Rotary tools for threaded fasteners — Performance test method

-

Non prevista

Esegui il login per scaricare i documenti

Espandi

ISO 4376:2024

ISO 4376:2024

Cycle energy requirement — Test method

-

Non prevista

Espandi

ISO 13707

ISO 13707:2000

Petroleum, chemical and gas industry services - Reciprocating compressors

Requirements for moderate to low speed reciprocating compressors and their drivers
for use in petroleum, chemical, and gas industry services.

Non prevista

Esegui il login per scaricare i documenti

Espandi

ISO 5389

ISO 5389:2005

Turbocompressors - Performance test code

ISO 5389:2005 applies to performance tests on turbocompressors of all types. ISO 5389:2005 does not apply to fans and high-vacuum pumps, or to jet-type compressors with moving drive components.

Turbocompressors comprise machines in which inlet, compression and discharge are continuous flow processes. The gas is conveyed and compressed in impellers and decelerated with further increase in pressure in fixed vaned or vaneless stators.

ISO 5389:2005 is intended to provide standard provisions for the preparation, procedure, evaluation and assessment of performance tests on compressors as specified above. The acceptance test of the performance is based on this performance test code. Acceptance tests are intended to demonstrate fulfilment of the order conditions and guarantees specified in the contract.

Non prevista

Esegui il login per scaricare i documenti

Espandi

ISO 10440-1

ISO 10440-1:2007

Petroleum, petrochemical and natural gas industries - Rotary-type positive- displacement compressors - Part 1: Process compressors

ISO 10440-1:2007 specifies requirements for dry and oil-flooded, helical-lobe rotary compressors used for vacuum or pressure or both in petroleum, petrochemical, and gas industry services.

Non prevista



Norme ritirate

Codice progetto

Codice Norma

Titolo

Sommario

Pubblicazione UNI

ISO 8662-2

ISO 8662-2:1992

Hand-held portable power tools - Measurement of vibrations at the handle -- Part 2: Chipping hammers and riveting hammers

Supplements ISO 8662-1 and describes a type test procedure for establishing the magnitude of vibration in the handle of chipping hammers and riveting hammers. The power tools covered may be electrically, pneumatically or hydraulically driven, or driven by means of an internal combustion engine. Annex A gives a definition of the basicentric coordinate system, Annex B a model test report.

Non prevista

ISO 8662-3

ISO 8662-3:1992

Hand-held portable power tools - Measurement of vibrations at the handle - Part 3: Rock drills and rotary hammers

Supplements ISO 8662-1 and describes a type test procedure for establishing the magnitude of vibration in the handle of rock drills and rotary hammers. The power tools covered may be electrically, pneumatically or hydraulically driven, or driven by means of an internal combustion engine. Annex A gives a definition of the basicentric coordinate system, Annex B a model test report.

Non prevista

ISO 8662-6

ISO 8662-6:1994

Hand-held portable power tools - Measurement of vibrations at the handle - Part 6: Impact drills

Specifies a laboratory method of measuring the vibrations occurring at the handles of hand-held power driven impact drills. It is a type test procedure for establishing the magnitude of vibrations at the handles of impact drills operating under a specified load. It is intended that the results can be used to compare different power tools or different models of the same type of power tool.

Non prevista

ISO 8662-7

ISO 8662-7:1997

Hand-held portable power tools - Measurement of vibrations at the handle - Part 7: Wrenches, screwdrivers and nut runners with impact, impulse or ratchet action

-

Non prevista

ISO 8662-8

ISO 8662-8:1997

Hand-held portable power tools - Measurement of vibrations at the handle - Part 8: Polishers and rotary, orbital and random orbital sanders

-

Non prevista

ISO 8662-9

ISO 8662-9:1996

Hand-held portable power tools - Measurement of vibrations at the handle - Part 9: Rammers

Describes a laboratory method of measuring the vibrations at the handles of hand-held power rammers used in foundries, on building sites etc.. Establishes the magnitude of vibrations at the handles when operating on the specified load.

Non prevista

ISO 8662-10

ISO 8662-10:1998

Hand-held portable power tools - Measurement of vibrations at the handle - Part 10: Nibblers and shears

-

Non prevista

ISO 8662-12

ISO 8662-12:1997

Hand-held portable power tools - Measurement of vibrations at the handle - Part 12: Saws and files with reciprograting action and saws with oscillating or rotating action

-

Non prevista

ISO 28927-1:2009/Amd

ISO 28927-1:2009/Amd 1:2017

Cupped wire brushes

-

Non prevista

ISO 8573-2

ISO 8573-2:2007

Compressed air -- Part 2: Test methods for aerosol oil content

ISO 8573-2:2007 specifies test methods for the sampling and quantitative analysis of oil aerosols and liquid oil that can typically be present in compressed air.

Non prevista

ISO 11148-6

ISO 11148-6:2010

Hand-held non-electric power tools - Safety requirements - Part 6: Assembly power tools for threaded fasteners

Scope not available

Non prevista

ISO 8662-5

ISO 8662-5:1992

Hand-held portable power tools - Measurement of vibration at the handle - Part 5: Pavement breakers and hammers for construction work

Supplements ISO 8662-1 and describes a type test procedure for establishing the magnitude of vibration in the handle of a pavement breaker or hammer operating under a specified load.

Non prevista

ISO 8662-4

ISO 8662-4:1994

Hand-held portable power tools - Measurement of vibration at the handle - Part 4: Grinders

The method specified is a laboratory type-test procedure for establishing the magnitude of vibration in the handle of a power tool fitted with a specified test wheel.

Non prevista

ISO 28927-1

ISO 28927-1:2009

Hand-held portable power tools - Test methods for evaluation of vibration emission - Part 1: Angle and vertical grinders

This part of ISO 28927 specifies a laboratory method for measuring hand-transmitted vibration emission at the handles of hand-held power-driven angle and vertical grinders. It is a type-test procedure for establishing the magnitude of vibration in the gripping areas of a power tool fitted with a specified test wheel and run under no load conditions.

Non prevista

ISO 1217

ISO 1217:1996

Displacement compressors - Acceptance tests

This International Standard specifies methods for acceptance tests regarding volume rate of flow and power requirements of displacement compressors.

Non prevista

Esegui il login per scaricare i documenti





Viale Elvezia, 12 - 20154 Milano
Tel. +39 02 266.265.1
Fax +39 02 266.265.50
P.IVA 11494010157

Social CTI

Seguici!

Twitter LinkedIn

Disclaimer - Privacy