CT 254 - Componenti degli impianti di riscaldamento - Emissione del calore (radiatori, convettori, pannelli a pavimento, soffitto, parete, strisce radianti)

00130011

EN 14037-1.2003

Ceiling mounted radiant panels supplied with water at temperature below 120 °C. Technical specifications and requirements

This Standard defines the technical specifications and requirements of ceiling mounted hot radiant panel fed with water at temperature below 120 °C supplied by a remote heat source.This Standard also defines the additional common data that the manufacturer shall provide to the trade in order to ensure the correct application of the products.

Non prevista

00130016

EN 442-1:1995/A1:2003

Radiators and convectors - Part 1: Technical specifications and requirements

Drafting of Annex ZA in relation to Mandate 129 (EC Directive 89/106).

Non prevista

00130017

EN 442-2:1996/A2:2003

Radiators and convectors - Part 2: Test Methods and rating

Drafting of Annex J concerning traceability of the thermal output measurement of radiators and convectors.

Non prevista

00130012

EN 14037-2:2003

Ceiling mounted radiant panels supplied with water at temperature below 120 °C. - Test method for thermal output

This standard describes the test method and the test installation for determining the thermal output of ceiling mounted radiant panels.

Non prevista

00130013

EN 14037-3:2003

Ceiling mounted radiant panels supplied with water at temperature below 120 °C. - Rating method and evaluation of radiant thermal output

This standard describes the procedure to determine the rated thermal output and the mean surface temperature

Non prevista

00130019

EN 1264-2:2008

Water based surface embedded heating and cooling systems - Part 2: Floor heating: Prove methods for the determination of the thermal output using calculation and test methods

This European Standard specifies the boundary conditions and the prove methods for the determination of the thermal output of hot water floor heating systems as a function of the temperature difference between the heating medium and the room temperature.The thermal output is proved by a calculation method (Clause 6) and by a test method (Clause 9). The calculation method is applicable to systems corresponding to the definitions in prEN 1264 1 (type A, type B, type C, type D). For systems not corresponding to these definitions, the test method shall be used.

Non prevista

00130020

EN 1264-5:2008

Water based surface embedded heating and cooling systems - Part 5: Heating and cooling surfaces embedded in floors, ceilings and walls — Determination of thermal output and cooling output

This European Standard applies to water based heating and cooling systems embedded into the enclosure surfaces of the room to be heated or to be cooled. Part 5 of this standard deals with the recalculation of values determined in Part 2 of this European Standard for the system in question, using it for floor heating applications. The recalculation method described in this part of the standard enables the conversion of the calculation and test results of Part 2 into results for other surface orientations in the room, i. e. for ceiling and wall heating, as well as for the application as cooling
surfaces, i. e. for floor, ceiling and wall cooling. It has to be emphasised that the test results of Part 2 of this European Standard are the basis of all calculation. Therefore the use of this prove method is necessary whether or not the system in question is used for heating or cooling application.

Non prevista

00130021

UNI EN 1264-1:2011

Floor heating - Systems and components - Part 1 : Definitions and symbols

The important definitions and symbols for water based surface embedded heating and cooling systems are specified in this standard.

Non prevista

00130022

EN 1264-3:2009

Water based surface embedded heating and cooling systems - Part 3: Dimensioning

This European Standard applies to heating and cooling systems embedded into the enclosure surfaces of the room to be heated or to be cooled. This document deals with the use in practical engineering of the results coming from part 2 and 5 and is applicable to floor-, ceiling- and wall heating systems, as well floor-, ceiling- and wall cooling systems.

Non prevista

00130023

EN 1264-4:2009

Water based surface embedded heating and cooling systems - Part 4: Installation

This European Standard applies to heating and cooling systems embedded into the enclosure surfaces of the room to be heated or to be cooled. This document specifies uniform requirements for the design and the construction of heating and cooling floor, ceiling and wall structures to ensure that the heating/cooling systems are suited to the particular application. The requirements specified by this Standard apply only to the components of the heating/cooling systems which are part of the heating/cooling system. This document excludes all other elements which are not part of the heating/cooling system.

Non prevista

00130009

EN 1264-4:2001

Floor heating - Systems and components - Installation

This European Standard is applicable to hot water floor heating systems as defined in EN 1264-1:1997. This European Standard specifies uniform requirements for the design and the construction of heated floor structures to ensure that the underfloor heating system is suited to the particular application. This European Standard specifies only the particular requirements which are dependent on the floor heating. This European Standard is not applicable to the other elements which are part of all floor structures (heated or not).

Non prevista

00130041

EN 1264-2:2008+A1:2012 (UNI EN 1264-2:2013)

Water based surface embedded heating and cooling systems - Part 2: Floor heating: Prove methods for the determination of the thermal output using calculation and test methods

The amendment consists in a new Annex C concerning the laminar flow

Non prevista